Need some advice: 

My car swerves when stopping.  The mechanic noticed the problem when he drove the car and he adjusted all of the vehicle’s drum brakes.   He, noted the brakes and drums looked good and the car has had an updated Master Cylinder installed.  Since the car was swerving to the right, we both believed the driver's side brakes were out of  adjustment, and they did appear to be the problem.  But the car still swerves when stopping.

I want to keep the car as original as possible, but this swerving issue is nerve-racking.  Here's my dilemma, should my first course of action be getting  the original drum brake system and front suspension inspected and working properly or should I just consider converting to disc brakes.  

 What's your advice?

Views: 72

Reply to This

Replies to This Discussion

The factory brakes when working properly are great so I'd go with that. I can't speak to disc upgrades since I've never done it but I have read many stories of clearance issues and other complications associated with that modification.

How are your brake hoses? If original or very old that can swell under the crimped portion. That can block off the flow of the brake fluid. I replaced my hoses recently and found that the right rear brake hose was swollen shut. Essentially only 3 wheels were braking which caused the car to veer left. It stops straight and evenly now.

Thank you Kurt

The suspension has alot to do with driving and braking straight. The entire front suspension needs to be inspected and repaired if needed. I loose idler arm will also cause a pull when braking. 

Thank you Russ

I had the same problem.  New springs and hardware solved the problem.  There’s a vendor on eBay that sells a kit for all 4 wheels for like 50 bucks.   My brakes work beautifully,  I don’t see how disks could work any better.  

Thank you Phil

post a pic of the master cylinder first.   The system is split front to back, not left to right, so it's pretty likely that the master cylinder can be ruled out, unless the installer added a lot of plumbing.

if the brakes have been adjusted, let's assume that is ok enough and didn't solve the problem.

First, bleed the brakes.  Air in one wheel cylinder will create this condition, so make sure it's not just that.

Second, check out the hoses.  They are 99% of the time the cause of this problem.   You can't do that visually, a bad hose swells internally to create this condition, so you have to test it in action.   Lift up  the front wheels, both at the same time is the best, but you can do one at the time too.   Have someone push and hold the brake, while you try to spin it by hand (tire on works best).   If it locks up and can't be moved, have the helper let off.  The wheel should spin immediately upon release.  If it does not, the brake hose is restricted, and the fluid is slowly flowing in and out of it.  You will find the bad hose is opposite the side of the swerve.  Replace both hoses if one is restricted 

If both sides apply and release normally on the test, go inside and check out the condition of the brakes hardware and backers.

I'd hope the mechanic would be able to tell the difference between front end and brake problems, but that is the final possibility.   To the idler arm, i'd add the strut bushings that attach to the frame by the bumper being gone, that would defininitely cause this condition, but a mechanic should immediately tell by feel whether it is brakes or suspension.   you'd hope.


No need for disc brakes as far as bringing these Cadillacs to a ——perfect quick stop when brakes are working as they should 

The simplicity of being able to change disc pads has some advantage 

My brakes have not faded once —since my 64 was new 

Car stops aggressively 

I use only Raybestos brake shoes as they do what was done to brake shoes back in the day 

They cut the shoes to match the drum ( like the local auto parts store did in there machine shop in the back of the store  ) and have a superior friction material for these very large drum brakes 

Replacing the  old worn  brake springs is a good idea ( to return the shoes ) 

All other posts have very good points 

Worn rubber brake hoses will flex ( buldge) and not provide the support needed - i second that 

 I would recommend ——cleaning  up and getting the self adjusters to be working for the convenience they afford 

Put some time into getting the stock brakes to work - it is less expensive and will be all the braking you will ever need 

Bleed the brakes and replace the brake fluid every few years to prevent rust in the brake cylinders helps

The brake peddle should move about one half inch and get  real real hard under foot when right 



If you need any brake parts, I have new (maybe 100 miles on al parts) cylinders, hoses, hardware and even drums were turned right before i installed it all.

I switched for discs cuz got fed up with trying to adjust drums and whenever I barely touched brakes while going slow, myself was about to go through the windshield.



  • Add Photos
  • View All


64 caddie Brake drums

Started by mark zimmerman in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 3 hours ago. 1 Reply

Are the front  brake drums the same as the rear ones? I had my garage install new drums on the car and now at 25-35 mph the car shakes like the  front wheels are going to fall off. Car has new brakes…Continue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 3 hours ago. 286 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Caddy Cruising with the Family

Started by Jason Edge in General Discussion 13 hours ago. 0 Replies

I've had a great couple of weeks entertaining family since Oct 11, and the 64 Caddy has played a big part.  Knowing aunts and uncles and many other relatives would be joining us for a celebration of…Continue

64 front passenger fender removal

Started by Chris Mcdougal in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 15 hours ago. 1 Reply

Hey guys I have search around the discussion boards and can't find anything.. but trying to get this passenger front fender off of my 64 deville 6 window got all the obvious ones and the one behind…Continue

Tags: removal, Fender

Blog Posts

Rochester throttle body gasket

Posted by Phil on September 29, 2021 at 8:18am 5 Comments

Hello,  would anybody be able to tell me if I’m using the correct gasket on my Rochester throttle body? It doesn’t  look right to me.  I’m not sure if the carb actually ran with this gasket because I got it used with no history.  Any help would be appreciated …


Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…


1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…


New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …



  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service