Long story short, I've replaced brakes etc which don't work! Did everything and finally found out that some of my vacuum lines were disconnected do to cracked ends etc and I've noticed that one vacuum line is missing.

Could any of you owners of 1963 Cdillac with an AC Unit please take and post some photos of the vacuum lines coming out of the firewall and where they're connected to??
Would be great if you could take the air filter out of the carb for the better view!

Sincerely
Mack

Views: 773

Reply to This

Replies to This Discussion

It does have the propotioning valve under the MC...
I'm going to bleed it one more time, one line at the time, crossing my fingers.

On my 72 chevy truck, the proportioning valve must be locked out, in order to bleed the brakes.  Check with the manufacturer of yours, to see if there is a procedure to bleed the brakes with their product installed.

I'll check it out however I've talked to the tech support of ABS Brakes System who sold me that kit and didn't mention anything about it...

All I am going to do next is to bleed every wheel one more time and IF it doesn't help then I'll disconnect MC and plug to see if it gives me the hard pedal! Then if it is hard, I'll check it by disconnecting the prop valve, if it's still hard then I'll disconnect and plug all outlets at wheels, maybe this will help me locate the problem...
I am already thinking about the faulty caliper at one of the wheels.
When bleeding brakes
Do not let the MC get low on fluid at any time
Keep it full as you pump the fluid thru the lines

Enjoy

Have you changed out all of the rubber brake lines, to include the rear as well? 

Last thing to check is that the piston in the master cylinder is wrong, or that the push rod is out of adjustment.  The push rod will travel in before it starts to push in on the master cylinder piston. It will give the feel of a soft brake pedal.  Seen it happen once, and it was baffling for days before it was figured out. A deep holed piston was installed, when a shallow hole piston was needed.

Google brake booster push rod adjustment to see how to get the correct measurement on the adjustable push rod.

Feels like Russ is on to something with the brake booster rod adjustment as you do have a new one installed

Enjoy
Mack
Did you understand Russ's note about the back of the MC plunger surface
Some of the plungers have a flat back surface and others have an indentation at the back of the plunger
If you have the chance check your old one to the new one
Depending on which one your new MC has you will have to readjust the rod in the brake booster to have the MC work as intended

I keep thinking the MC is not working as it should so this solution seems like it could be the answer to your issue to me


Enjoy
Mack
You may have to change your MC depending on the shape of the back surface of its plunger to have the brake system work correctly
Compare the old MC plunger to the new one to see what you had before and what you have now

Russ is indicating the flat back plunger is correct for our cars and the indented one will not work

Enjoy
I know what you guys mean
Here's the photo of that 'old' MC. New one look the same.
I think I'll take it out tomorrow to measure the depth of the MC and the Boosters rod's length to see if there's any unwanted empty space between those two.

Well, and it supposed to be the 'bolt on' conversion kit... Haha
Attachments:
Mack
Both the MC and the brake booster have to be the same brand
They both have to be Delco Marain ( most avaiable and cheeper ) or both Bendix as they used two different kinds in our year cars
You said something about the MC being replaced by someone
Did they give you the correct match for your booster at that time ?

Enjoy
Mack
If you have the old brake booster examine the old and new to see any differences in look and brand and the rod length you are looking at

If both are the same brand then i would think the the rod length is the fix

If you had a leak of some kind in the braking system ( or a bad MC ) the peddle would go to the floor and you would see and smell brake fluid coming out of someplace under the car or on the back of the tires ( bad brake cylinder )

Hang in - we will get to the bottom of this
I am looking foward to the solution to this problem

Enjoy

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

1964 Cadillac Deville - TH400 kickdown switch

Started by Louis in Wanted to Buy. Last reply by Charles Fares 9 hours ago. 1 Reply

Hello,I am searching for a  TH400 transmission kickdown switch (the one near the carburetor). A new one or in good condition.I already asked Fatsco and US Parts Supply but they don’t have this…Continue

New Gallery

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion 11 hours ago. 0 Replies

I am truly fascinated by the  wonderful  inspiring stories behind owning these 63-64 CLASSIC ANTIQUE CADILLACSThey have set the website ON FIRE !!Jason Mr Webmaster your talents regarding the subject…Continue

64 429 Thermostat Housing

Started by Jason A in General Discussion. Last reply by Russ Austin 14 hours ago. 1 Reply

Does anyone know where to find a thermostat housing for a 64 429?  Are any cars interchangeable?  Chevy 350 looks identical, but a lil bigger.Thanks,JasonContinue

New photo gallery

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 17 hours ago. 8 Replies

Having trouble posting my picture in the new gallery but managed to get the text right The computer WIZ - I am NOT ! Stay safe my friends Continue

Blog Posts

How to sensibly deal with the Corona Virus

Posted by Jeff Kinzler on March 14, 2020 at 5:02pm 6 Comments

https://theamericanscholar.org/covid-19-a-primer/

I found this very helpful, written by a knowledgeable authority in public health. 

Remember, Viruses are not spread by Cadillacs so get out and drive!


Safe & Healthy travels. 

Jeff Kinzler

1963 Eldorado convertible boot

Posted by Les Eastling on February 27, 2020 at 10:33am 1 Comment

I need a used convertible boot for a 63 Cadillac convertible - condition or color is not an issue since it will be used as a pattern for making a new one. One from either a 62 series convertible or an Eldorado would work. I know I am searching for hen's teeth here... but you never know unless you ask!

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service