On a 1964 60 Special with a tilt wheel, tubro trans and #653 neutral switch.  When I had the transmission done the switch got out of alignment.  Now the car will start in Park, but not in Neutral, and the backup lights will not light.  If I move the switch so the car will start in Neutral, it will not start in Park, and the back up lights will not light.  If I move the switch so that the back up lights will light when in reverse, the car will not start in Park or Neutral.  Does this mean I need a new Neutral Switch?

Rob  

Views: 87

Reply to This

Replies to This Discussion

it could be, but not as likely as the pivot for the linkage in the frame either was destroyed or left out when the trans was replaced.  If you have slop in the selector quadrant, and no one touched your column especially, that's 99% the cause.

What should I look for to determine if the pivot for the linkage is there?  Is this the area which is described in the shop manual on page 10A-29 in photo 10A-21?

you should go under the car, and find where the linkage goes into the frame under the driver's seat.   Just wiggle the shaft at the frame end, if there is play, that's the problem.   It should be a ball-shaped bushing, which is known to wear out, and a spring to keep it tight on the frame.  

Mark 

I had no idea about this   
Thanks 

Enjoy 

If it has worn out, how can it be repaired?  


I would suggest you remove the  NSS and inspect it for damage to be sure it is not causing your problem getting it adjusted to do all it does correctly 

They can often break and  but can be repaired if damaged 

Getting a look at it could be helpful before you next move 

I have no idea what the pivot thing is  that is being discussed but love to know what that is about 

Enjoy 

Anders 

Nice work —-if  it is his NSS that needs repair that will help him get it repaired 

Mark seems focused on another location causing the treads problem  that is foreign to me so learning what I can about it as we go 

Enjoy 

Do we happen to have a picture available of  the round bushing and spring ( gear selector pivot thing ) that  Mark  is explaining and referring to which is causing the issue in this tread ??

Enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

Rear main seal. 63

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 16 hours ago. 3 Replies

My rms is leaking again.  I hv cked all other options for leaks and its none of those.  Ie, oil presdure, valve covers, etc.  So i called egge to order another one.  I asked the guy wat contack…Continue

Selling 1964 Coupe Deville Parts

Started by Gary Smiley in For Sale. Last reply by Gary Smiley 17 hours ago. 2 Replies

What I  have are many extra original, hard-to-find 1964 Cadillac Coupe Deville Parts (from donor car).…Continue

Tags: doors, hood, engine

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 275 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service