Hey guys, I'm having a local shop try and seal up some of the leaks on Ol Blue, '63 SDV. I've got a couple questions.

Has anyone replaced the tranny shift shaft seal, are they available? Is it doable without a total tear down?

I already have the pan, rear main, valve cover gaskets. I've read all the  war stories about rear main, and various other problems. Anyone ever seen rubber valve cover gaskets? All I can find is cork rubber.

Thanks for any info.

Tom B

Views: 89

Reply to This

Replies to This Discussion

Tom 

The stock valve cover gaskets were cork

I do not know of any rubber myself 

I read that you should soak cork in water before installing them and it does make sense they would get thicker and be more pliable and flexible which could help them  seal although I have not yet tried that technique  myself 

Do take the time to be sure the valve cover metal  lips are very square and straight by aligning them on a 2x4 

Unlike may others valve covers these will flex if you tighten the bolts down to hard which will cause leaking issues and a bad seal on new gaskets so torque to spec 

These valve covers are a little more of an issue to get  sealed correctly than others 

Enjoy


Do be sure to find Russ Austin’s post  on the rear main crankshaft seal —-that indicates he offset his rear main seal by one inch off the crankshafts rear main bearing joint which is the most successful attempt to get that seal to stop leaking in many attempts to get that done over the years on this site 

All  prior threads on this site are located at the —Search -on the top right of the home page 

A leak free pride and joy is a nice thing to have 

Enjoy 


Giving anyone working on your Cadillac your copy of your cars year Service Manual  should  be a good Idea 

—the details he needs are all located there 

Enjoy 

I prefer the thick cork valve cover gaskets. I would never use one of those thin rubber valve cover gaskets. With a straight valve cover that has not been overtightened (they can be bent back with boards and a heavy hammer if they have), and the correct thick cork gasket (no sealant needed) and torqued to 28 inch lbs (2 1/3 ft lb), it should never leak. 

Thanks all. Not so concerned about valve covers and will pass along info on pan and rear main seal, contact cement, etc.

Only questions left is on tranny. I assume the dip stick tube is just an O-ring. What supplier has the shift shaft seal? Is it doable in car at same time? Thanks all.

Shifter seal is very straightforward and can be done on-car.

Take off pan, disconnect linkage.  Inside transmission, just loosen a clamp and a set screw and the shaft slides out.
The seals on the hydramatic are o rings, on turbo hydramatic there is a small lip seal.
Fatsco will have all of them.

The trans dip stick tube is an O ring recessed in the hole of the trans.  Taking the pan off and going through the bottom of the trans would be the best way. I did mine with the engine out and through the top. 

Just use the black form a gasket RTV at the base of the dip stick and follow the instructions. 

Thanks for all the info. I feel a little more confident in getting some decent results on this adventure.

Tom B 

RSS

Photos

  • Add Photos
  • View All

Forum

Whoa there, you want how much??

Started by Robert Gonzalez in 1963/64 Cadillac Specific Discussion 15 hours ago. 0 Replies

Ok, I’ve been on here for almost a decade. I KNOW we covet our cars and have always tried selling them at premium prices. But the bottom line, our cars rarely fetched prices over a covair. The…Continue

1964 Cadillac parts for sale... northern cali

Started by Jason in For Sale. Last reply by Jeremy yesterday. 1 Reply

Bill Hirsch cast iron gray exhaust and manifold paint (1 can) $20Bill hirsch Cadillac dark blue engine enamel high temp high gloss (2 cans) $40Convertible top latchValve coversHeadlight bezelRadioGas…Continue

Tags: Parts

63 4 door Cadillac

Started by Walt Timmerman in For Sale. Last reply by Jeremy yesterday. 7 Replies

Need to start parting this car out. Might be moving soon and if its not parted out, it'll be scrapped.Also have Motor and transmission from my 63 coupe deville for sale. will part out also.Was told…Continue

Free- 64 lower bumper bucket - Passenger side

Started by Michael Buonaccorso in For Sale. Last reply by Jeremy yesterday. 1 Reply

This is in rough shape. Not only is there rust in the usual places but it is also bent. I replaced this piece on my car after an accident, but since this is a hard to come by piece, I figured someone…Continue

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service