On Friday I did install power antenna.When I try to raise the mast by pulling knob on the radio -mast didn't go up.I heard strong antenna motor clicking.I try to pull with plyers top of the mast and I realized that mast is going down while pulling  radio knob.Looks like antenna works when going down but not going up.What is the problem?What I did wrong.I did replace cable connecting radio with antenna.I did connect blue wire with blue and green with green wire.Before restoration antenna was working fine.Maybe the knob on the radio that control antenna have something to do it? I did lubricate mast with WD-40.

Thank you,

Paul

Views: 127

Reply to This

Replies to This Discussion

what happens when you push the radio knob rather than pulling it?

It is only react when I pull up.

put a test light on the green wire while somebody pushes the knob, if it gets power, replace the antenna motor. if it doesn't then it is likely the switch inside the radio.   could also be a broken green/white wire or bad connection at the firewall.

Pushing the  radio nob in should raise the antenna when it is working correctly 

I do think your new antenna motor is your issue 

Motor needs to be working in both directions 

Do be very sure your ground connection is cleaned and shinny metal but the motor is working —only not  in both directions 

The clicking sound is normal when the antenna is all the way down 

Enjoy 

The antenna is original from the car -not new.Maybe the radio knob I installed differently-because when I pull out the knob I have feeling like the antenna want to go down (it is already down).

  "It is only react when I pull up."   What does that mean?  Are you pushing the radio knob in?  The knob is designed to push in and pull out to raise and lower the antenna.  Check the wire connector for a pin that has pushed out. The plastic connectors get weak and brittle from being exposed to the elements. It has happened to me before, that a pin pushed out of the connector when they were mated together.

Push nob —is up 

Pull nob —is down 

Enjoy 

- Did you bench test antenna before installing? 12 volts to green pushes out, 12 volts to blue pulls in. If not, you can disconnect antenna connector at bottom right of firewall cowl and test via a 12 volt source to green then blue wire with antenna in car.

- Are you firmly pushing radio knob in? It takes some effort. Might take some tuner lube cleaner like the CRC sprays and push and pull the knob back and forth. If it is not pushing in and a spring action felt to push it back out something might be broken on the radio knob switch.

- Is knob correctly installed on shaft at the normal detente position with the Allen set screw?

- Is the connector at bottom right of cowl/firewall making good contact. Did you clean the metal inside the connectors to makes sure they make solid contact. It sounds like you spliced some wires... did you make sure everything was making good contact? 

- And as noted previously, you can disconnect the antenna connector and test for 12 volts on the car side connector for 12 volts at green when pushing knob in, and 12 volts at blue when pulling knob out. 

If you are pulling on the nob and the antenna is already down it is working correctly. ( on that side )  and will make a clicking sound when bottomed out 

you need to get the motor to rise —when you push in the nob 

Marks suggestions should help find the electrical issue and get the motor working correctly 

Clean the mounting locations  as they are the electrical grounds so clean them to shiny metal as that will make for good electrical flow to the antenna  motor 

Enjoy 

Ok,problem solved.

When I installed the knobs on the radio I push the top knob too far and didn't let me use the function to push antenna up.

Thank you for all suggestions.

Yep, just got to let the knob set at that "detente" position when setting the Allen screw.  Glad you figured it out!

Jason 

Really nice job realizing the nob  location issue was the problem 

Where else could you ever get this kind of  spot on repair info for such a specific  unique repair 

This place  and the individuals ( you know who you are )  here are just the best for this type info ( repair ) for our year cars that is so very specific to just our year Cadillacs 

Liked watching this difficult problem getting worked threw myself 

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 5 hours ago. 20 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

A Before & After Example

Started by Jason Edge in Restoration Discussion yesterday. 0 Replies

Since I started cadmium plating the many fasteners and other items from the 55 and counting parts cars I have bought in (1200 lbs worth and counting), I have to say it has really taken the…Continue

Oil leaking out of oil cap breather

Started by mark zimmerman in Restoration Discussion. Last reply by mark zimmerman yesterday. 12 Replies

Hi i would like some ideas on this i replaced oil cap breather and pcv valve and still oil  coming out of breather at normal speeds down the road.This has been going on for quiet awhile from the…Continue

Update on fuel pump

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by William R Conte yesterday. 1 Reply

I'm still looking thru land and sea for this fuel pump anyone out there know what size engine I have here are some pics of the stamps on the block I found to make sure my engine is a 390 because the…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service