Hello everyone,
I’m rebuilding the power steering pump on my 63 Park Ave and ran into a problem. The shaft bushing that came in the rebuild kit is slightly larger in diameter than the original. It is stamped F11 like the original but it’s maybe
1 mm larger in diameter and won’t press in, I couldn’t set it in to start to press it in. I’m sure someone here can point me in the right direction locating the correct bushing.
Thanks Kraig

Views: 103

Reply to This

Replies to This Discussion

I thought for sure someone here would’ve answered my question by now haha. Well I guess it’s time to buy another rebuild kit from a different manufacturer and keep my fingers crossed it’s the correct bushing

Take the parts and pump to a machine shop to have the bushing machined down to fit.

That would work but since posting I’ve realized that the ID is also larger so I really just need to find a bushing the same size as the original 

Would not a replacement used power steering pump help solve your problem and be a simpler solution than finding parts for the one you have now that may be a problem To locate ?

Enjoy

RSS

Photos

  • Add Photos
  • View All

Forum

Roof trim

Started by Krystin Barany in 1963/64 Cadillac Specific Discussion. Last reply by Krystin Barany 1 hour ago. 2 Replies

I’m going to be starting to tear down my 64’ DeVille before too long but one thing I never figured out was how the roof trim comes off. I understand the drip rails and how to take those off without…Continue

Factory AC clutch fan needed

Started by Chris Gill in 1963/64 Cadillac Specific Discussion 4 hours ago. 0 Replies

Hi folks,My clutch fan died so I desperately need a new one. Unfortunately it will take a week or more to order from the usual suppliers so I am hoping someone on here has a manufacturer name and…Continue

Replacement Rear Trailing Arms

Started by Dan McNarry in Restoration Discussion. Last reply by Kim K Kaiser 8 hours ago. 5 Replies

Hello all,I haven't been on the forum for quite a while and do wish you all well. I would like to thank all of you who have purchased replacement rear trailing arms from me in the past. I realize…Continue

Over heating

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 9 hours ago. 4 Replies

Hi, been doing the break in still. At about 450 miles.I hve noticed that when i go out, temp gets to between 1/4 and 1/2 on the gauge.  If i sit any period of time or dnt keep moving, it creeps…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service