All, I just replaced my rear driver side window motor. That was a fun time.

I have looked in the manual and searched the site and cant seem to find any info on my new problems.

The speed of the window. It rolls up so fast is slams into the top rail of car.  Is there away to slow the window down ?

The window is loose in the frame is wiggles with full up. 

The window slides back down  1/4 inch or so when rolled up. 

I appreciate the help. You all are a wealth of knowledge.



Views: 93

Reply to This

Replies to This Discussion

Your window is rising faster than the norm from your explanation and not stopping at the top more softly as it should 

Do you have the correct window motor for your application ?
Where did you get the motor ? 

Sounds like you are having window track issue for the window to rattle and drop back the 1/4 inch 

There is no way —I know of - to slow a stock window motor down  as it should not be necessary with the right window motor

Mostly feels like you do not have the correct window motor for your year Cadillac with the issues you are having with speed and hitting the top so hard 


Best I can do with the explanation you gave 


Yes you are correct. It goes up to fast and slams into the top of the door frame.

I bought new motor off of eBay. It looked exactly like the one I took out.

How does one fix the window tracking issue ?

Do you have the rubber window bump stop at the top of the vent window? That should keep it from slamming. 

I would suggest you purchase a window motor from Jason Edge on this site that will be the correct one for the  car you have 

He is at the top of the parts supplies page in the header 

Most of the window motors will look the same but could have different calibrations having been used in many different cars with different needs and specs 


Regarding the window track 

Get a good look at it and see what’s going on for it to be keeping the glass lose 

Study the mechanisms movement 

You might be able to acquire a new assembly ( or parts needed ) and install it if you see what needs replacing and your skills allow you to do that 

Jason could be your source for that also 


the scissor motion of the cams is designed to slow down the speed of the window while decreasing the load on the motor, so if your window is going faster than it should, it's because the scissor action is not occurring. 

bottom line, one of the rollers is not in the track, either on the lower cam or the sash cam.  The window is in 'direct drive,' so it's moving double speed, and not being contained fore and aft, so it's bouncing and wiggling.

You need to get the panel off and see put it back on track.  if the roller popped off, the regulator is bent, you will have to bend it back or the roller will pop off repeatedly.

Just to add I would say about 1 in 4 regulators have rollers with chunks broken off. They get old, dry and brittle and can break apart with age. I would leave the rear door panel off and get a good light and operate the window with switch plugged into the connector and watch it go up and down after you have confirmed the rollers are good and in the cam tracks. 

Just love when the community comes together to get to the bottom of a repair issue from guys with hands on experience and expertise  on  the subject presented 

Bin there — done that— always works for me regarding repair advice 

Love this site and the endless things I learn myself about our very great cars continually 

You GUYS  Rock—— and make this the great place it is 

This is Truly a Magical place ——for  63-64 Classic Antique Cadillac owners  to seek info needed for a given restoration repair  

How very special and rewarding is that my Cadillac Crazies !!!!!!!!



Thank you all for the advice. Finally had time to get back out and take a look. 

Window cams are in the tracks and scissoring. 

Window is only wobbly on one side, when I rock the window back and forth I can see where the cam is moving  in and out as well. I will get an inspection mirror and check to see if the cam is whole and not broken., 

I do not see a rubber stop. Where would it be located?

Might be as simple as one of those small screws or welds (some use screws some are welded) has come loose where the cam attached to window frame etc. If you end up just needing one of those small flat bevel head screws, I have plenty.

The rubber stop is on the front vent window frame so probably not applicable here. Maybe Fleetwoods and 6 window Sedans have them in the rear but I don't know (I have  a Coupe). I was thinking the felt covered window channels might be worn out but my Coupe has those on the front window channel only, not sure about Sedan rear windows.



  • Add Photos
  • View All


vacuum canister

Started by Walt Timmerman in General Discussion. Last reply by Rob Shatsnider 1 hour ago. 15 Replies

what is the vacuum canister for that is behind the drivers front fender?After removing my fender I see its got a hole in the top but nothing is hooked to it and no line is laying there.Any help would…Continue

New Batch of Embroidered Iron-On 1963/64 Cadillac Chapter Patches - $4 each

Started by Jason Edge in Chapter Discussion. Last reply by mark zimmerman 6 hours ago. 10 Replies

As noted in our August 1963/64 Cadillac Chapter Newsletter:Around 6 years…Continue

Tags: Available, Patches, Chapter, Cadillac, 1963/64

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Daniel Grande 14 hours ago. 9 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

64 deville choke heat tube

Started by Thomas Yarri in 1963/64 Cadillac Specific Discussion. Last reply by Thomas Yarri 15 hours ago. 2 Replies

Hey guys hope you’re having a great day. I have a question about the choke heater tube. Mine is loose at the intake and seems to be causing a vacuum leak. Any thoughts on how to seal this up?

Blog Posts

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …


Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…


Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment


Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…


Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow


  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service