Howdy all,

I'm working on restoring a 63 fleetwood I picked up with a fairly straight unrusty body but no engine/ transmission. Bought a 63 coupe in running condition but completely rusted through roof and trunk. Getting ready to pull the engine and tranny hopefully this week to start doing a rebuild on it before installing in the sedan. any advise? I psyched myself out about getting beneath these cars without one of them falling on me and crushing me, but I've been experimenting with some jack stands I bought and feel a little more comfortable. Would appreciate any advice on the safest way to go about doing this. One of the methods I read somewhere is taking the tires off of the front of the car and stacking them below it to act as a buffer in case the car comes falling own. 

Views: 121

Reply to This

Replies to This Discussion

Hi Cameron. Good to hear from you. You can remove the engine and tranny together from above with hood off the 63 Coupe parts car for better clearance. You will still need to disconnect and drain from the bottom. I use two jackstands at front of frame one to left and one to right with room to run a floor jack between and lift at that wide center frame section below engine.  I will of course have jackstand on solid flat surface and will drop the car onto the jack stand making sure they are securely cradled in jack stand supports. I leave the jack firmly in place providing support if anything did happen with the jack stands. You can also jack up and install short jack stands along the side frame rails.   You will of course want to make sure your cherry picker or hoist is  securely mounted tot he engine. If removing with the trans attached you will want to mount a bit rear ward to better balance the weight distribution since you would have the transmission attached. You can of course remove the shop manual way by removing the engine 1st from above, then the transmission from below, but since they both need to come out and it is a parts car, I would pop the hood off, drain fluids, disconnect from the bottom, and lift both engine and transmission out.

thanks for the feedback. Planning on pulling the engine with the transmission attached. I just need to get beneath the car to detach. I hadn't originally planned on taking off the hood but it makes sense to get more clearance. 

Several things to consider first, to remove the complete drive train you will have to remove the radiator and air conditioning condenser as the assembly is pretty long. It may come out without that removal but if something does go wrong (and it always will) anything that gets damaged Will be expensive to replace. Better to lift the engine out then remove trans from the bottom. The up side is if the donner car is rotten, a torch can help to get any stuff in the way out of the way. In addition the total weight is less if done in two stages. 

Thanks

RSS

Photos

  • Add Photos
  • View All

Forum

Web site up with a new design.

Started by Russ Austin in General Discussion. Last reply by Russ Austin 12 hours ago. 2 Replies

My web site has been down for a few months and I migrated to GoDaddy.com  Best move ever!My new web site rocks, hope you enjoy it.  …Continue

Had the 64 convert out for some Cruising around the town

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 5 Replies

It is 74 degrees sunny and dry in central Fl - what a day !! - Top Down of coarse The usual OOH’S and AH’S people encircling the car when parked -  a NICE yelling from a car  —and a what year is that…Continue

The 64 - 429 Cadillac gas engine —-is a special unique torque monster ! !

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

The 64 Cadillac gas engine is a torque monster —with 480 ft lbs of toque at 3000 RPMs Out of curiosity I looked up my 409 dual quad  425 HP  race engines   specs and it has only 425 ft lbs of torque…Continue

Blog Posts

Oil pump

Posted by Ray Schick on October 30, 2022 at 4:34pm 4 Comments

I removed the front cover to change out the timing chain & gears all that went pretty well when I put the cover back on I put in a fresh oil filter ,filled it up figured it would be enough to prime the oil pump when I started the car .Fired up the car and heard lifters rattling, So I shut the car down right away. So I removed the oil filter housing, and poured oil down the neck of the oil pump housing filled it up and filled up the filter put it all together and fired it up and same…

Continue

Available parts

Posted by Thomas Reichenberger on October 13, 2022 at 11:47pm 0 Comments

Caddy members, I’m upgrading my 64 2-door coupe deville.

motor guy lost my block (machine shop went under) so I’m replacing motor & tranny with LS conversion. I have motor parts (other than block) for 429, rebuilt transmission, converter, and too many other motor parts not needed with fully dressed LS going in.

Email me (Tom.reichenberger@ipsper.com) or call me (210-739-4854) if you’re interested…..I live in San Antonio, TX.

thanks, TX…

Continue

Trunk Open and Lock Mechanism is in Closed Position

Posted by Chris Anderson on September 13, 2022 at 7:14pm 7 Comments

While working on my trunk lock on 64 Cadillac, I mistakenly closed the locking mechanism while the trunk was open.  Is there an easy way to manually release the lock back to the open position?

Thanks.

Fuel Pump Failure

Posted by Jon Shields on August 6, 2022 at 6:48am 4 Comments

Hello,

I'm located in Melbourne, Australia and my 64 sedan de ville is stuck in the garage due to failed mechanical fuel pump. The first after market mechanical fuel pump lasted a few years before it failed & left me stranded 5 hours from home. A hire car and tow got us home. On inspection, I noticed a valve not seated within the housing. I was optimistic, pressed it into place and assumed the pump was good to go. But alas, no. From what I can now determine, the diaphragm pushrod…

Continue

Videos

  • Add Videos
  • View All

© 2022   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service