my name is Stefan and this is my first post in this forum. I´m from germany and very happy to own and drive a 1963 Fleetwood 60 Special in a very nice condition. It has been delivered by Cadillac Switzerland in 1963 to a 5* hotel in Portugal and was used as a VIP shuttle for guests.

A lot of technical issues have already been resolved , but there are still some ToDo´s on my list. I am very happy to have found this forum and looking forward to lots of good conversations and infos.

So my actual ToDo is an ignition upgrade to a Pertronix ignition.

Engine is the original 390cui with the stock Carter carburetor and ca. 52.000mls of total mileage.

My question is:

Do you have any recommendations for a Pertronix ingition? I, II or III ? with/without Lobe Sensor? 

Will the Pertronix I be completely sufficent, or do you recommend e.g. the II?

Thank you in advance for your help!

Views: 66

Reply to This

Replies to This Discussion

Grats on a 63 purchase, you wont be disappointed.  I recommend #3 as it offers the best protection and ease of installation. 

Running the points is also just fine.  I have the #2 on a 63 sedan and points on a 63 series 60.  Both run just fine.  

  The II or III is what I recommend The I has the weakness of failing if you leave the key on without it running. The II and III do not have this problem ,they also have adaptive dwell and sense cranking speed and retard the timing slightly only when cranking over to aid hot starting. The III has multispark which can make for a smoother idle.

I'm running the II and added the Flamethrower coil as well and have been very happy with it. There are details on each and installation tips under the Help tab In the header above.

Pertronix Ignitor Ignition & Flamethrower I, II, and III Compar... 

Pertronix II & Flamethrower II Installation by Anders



  • Add Photos
  • View All


Replacing Front Door Window Chrome Channel

Started by Michael Vogler in General Discussion 2 hours ago. 0 Replies

List Mates,My '64 De Ville Conv. front door window chrome trim needs to be replaced.  The chrome on both front door window his getting a little bit of pealing off.  I have the chrome replacement…Continue

Vacuum advance

Started by Thomas Yarri in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 15 hours ago. 1 Reply

Good afternoon to all my fellow Cadillac owners! I have a question about the vacuum advance on my car. The car is a 64 without a/c and a Rochester carburetor. I noticed that I have vacuum at the port…Continue

1963-1964 Convertible Parts

Started by Charles Fares in For Sale 22 hours ago. 0 Replies

1963-64 Convertible top switch with chrome bezel and mounting retainer clip, tested and working, nice chrome, $65. 1963-64 Convertible rubber A-pillar seals LH and RH pair (repops) $50 the pair.…Continue

Over heating

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 22 hours ago. 9 Replies

Hi, been doing the break in still. At about 450 miles.I hve noticed that when i go out, temp gets to between 1/4 and 1/2 on the gauge.  If i sit any period of time or dnt keep moving, it creeps…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…


New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …


Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…


Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment


Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…



  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service