Hi Guys,
I need to remove my door panels as I'm getting ready to do some bodywork. How do the ventilator window handles come off. I need to remove them to get the panel off. My door panels are pretty trashed along the bottom as well so I need to replace them at some point.

Thanks,

Alex

Views: 167

Reply to This

Replies to This Discussion

There is a wire horse shoe clip under the crank. You need a tool to slide it out. Sold at Napa or parts store. The bottom part of door panel is replaceable so don't trash them.
Thanks, I got the panels off, I've stripped the whole interior today so that I can replace the floor pans. One of the previous owners riveted in metal and then glass fibered over them.
The floor repair ,you plan on doing ,feels like it could be difficult ,due to the way it was repaired in the past
Like to know what your plan of attack is ,regarding replacing the floor pans ,in this case ,and condition
Is it most common to cut the bad out and weld or braze new in ?
Just like to know a little of what goes into ,replacing the less than solid ,floor pans
It's not difficult just time consuming. I'll get all of the previous repaired floors out first. They were riveted over the bad floors. From under the car drill guide holes along the floor braces so that I don't cut through them. Cut the old floors out back to good metal. I will then clean up the floor braces.

I'll then Cleco in the new floor pan temporary and with a sharpie trace on to the new pans. Trim to fit and then I will tack in place moving around from side to side to prevent heat build up with a mig welder. I have some body braces to repair as well. I cut good ones out of the 63 parts car I had. I'm off this week from work due to spring break so plan to get a lot of it done this week. It's a lot of work but I had to do the same on my 50 Chevy.
Sounds like a good plan to get the flooring solid again
What is Cleco ?
They are these pins. They are used in the aviation industry for panel placement. They are like reusable rivets.
Attachments:

RSS

Photos

  • Add Photos
  • View All

Forum

Is this possible or total BS?

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 5 hours ago. 5 Replies

After changing tie rods, i tokk car into wheel n allignment shop. He said no problem.  He calls back about 45 minutes later and said they couldnt get between the tire and cowl, the guys head was too…Continue

Vacuum / Parking Brake / NSS Question

Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion. Last reply by Karl Schwarz 6 hours ago. 2 Replies

I bought a 1963 Series 62 Convertible in July.It makes a hissing sound when in neutral, and sometimes when in drive (when the shift is more to the left that the right. I assume this related to a NSS…Continue

Tail pipe black stuff!

Started by Lambert Ross in 1963/64 Cadillac Specific Discussion. Last reply by Lambert Ross yesterday. 10 Replies

any ideas how to clear the ugly black stuff shooting out from my tailpipe? After a long layover, it really messes up the garage floor. I assume its carbon but am not sure how best to react to it.…Continue

Blog Posts

still need a driveshaft

Posted by wayne weaver on November 26, 2019 at 11:53am 0 Comments

well thank you UPS for losing the driveshaft that Russ Austin shipped me. 

however i still need a rear driveshaft section for my 63. mine has a vibration due to the bushing inside of it. its a shame because the ball and sockets in the cardian joints are perfect but it has a woble on the balancing machine. so .  still need the rear section. anyone have a good one ? is there driveshaft alternatives to use ? i am really considering an LS swap and since im fighting the driveshaft search…

Continue

63 guidematic issues

Posted by maurice lapoiinte on November 24, 2019 at 3:10pm 0 Comments

 So my 63 guide matic headlamps stay on low beam all the time. I have so far bypassed the system and everything works normal. I have been thru the trouble shooting in the manual but this is where the confusion begins.on my car when the power relay is powered I have low beam and when its not powered I have highbeam, this appears to be opposite what the diagnosis says should be correct.The wiring is all original and no wires have been mixed up.has anyone ever unplugged the 2 wire connector…

Continue

Another advantage of the Pertronix III

Posted by Doug Scarrow on November 23, 2019 at 11:12am 1 Comment

   Having tried both the II and III I can say the multispark feature of the III offers a smoother idle . It is also easier to install .Does not require removal of the distributor

Stuck at two red (dash) lights!

Posted by Jeff Kinzler on November 3, 2019 at 10:00pm 9 Comments

I hope someone can help solve these two electrical problems that appeared one after the other.

By way of background: The car, a '64 Eldorado has very limited use. It was at a restoration shop for 15 months until last January-  that supposedly did a bunch of wiring repairs including rebuilding the gas gauge that still hasn't worked properly, and the clock that hasn't worked, and re-soldering the broken wires in the drive door. All window and seat controls appear to be…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service