Hi Guys,
I need to remove my door panels as I'm getting ready to do some bodywork. How do the ventilator window handles come off. I need to remove them to get the panel off. My door panels are pretty trashed along the bottom as well so I need to replace them at some point.

Thanks,

Alex

Views: 171

Reply to This

Replies to This Discussion

There is a wire horse shoe clip under the crank. You need a tool to slide it out. Sold at Napa or parts store. The bottom part of door panel is replaceable so don't trash them.
Thanks, I got the panels off, I've stripped the whole interior today so that I can replace the floor pans. One of the previous owners riveted in metal and then glass fibered over them.
The floor repair ,you plan on doing ,feels like it could be difficult ,due to the way it was repaired in the past
Like to know what your plan of attack is ,regarding replacing the floor pans ,in this case ,and condition
Is it most common to cut the bad out and weld or braze new in ?
Just like to know a little of what goes into ,replacing the less than solid ,floor pans
It's not difficult just time consuming. I'll get all of the previous repaired floors out first. They were riveted over the bad floors. From under the car drill guide holes along the floor braces so that I don't cut through them. Cut the old floors out back to good metal. I will then clean up the floor braces.

I'll then Cleco in the new floor pan temporary and with a sharpie trace on to the new pans. Trim to fit and then I will tack in place moving around from side to side to prevent heat build up with a mig welder. I have some body braces to repair as well. I cut good ones out of the 63 parts car I had. I'm off this week from work due to spring break so plan to get a lot of it done this week. It's a lot of work but I had to do the same on my 50 Chevy.
Sounds like a good plan to get the flooring solid again
What is Cleco ?
They are these pins. They are used in the aviation industry for panel placement. They are like reusable rivets.
Attachments:

RSS

Photos

  • Add Photos
  • View All

Forum

Trumpet Horn

Started by Ray Schick in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 5 hours ago. 1 Reply

Check out the price for the trumpet horn on eBay , that’s crazy !   Someone really wants to blow their horn at that price.Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 17 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Front Disc Conversion for ‘64 Series 62 Coupe

Started by Dan Loukota in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 18 hours ago. 6 Replies

I started a front disc brake conversion on my ‘64 Caddy. I finished the drivers side first only to find my factory rim scrapes the caliper to the point it would need spacing 1” to clear and roll…Continue

Bucket seats

Started by Gregory Lewis Freeman in 1963/64 Cadillac Specific Discussion. Last reply by Ian Osborne yesterday. 15 Replies

I'm looking fo a set of 63 64 eldo or devilleBuckets with console and door seat controllersGreg 2133059550.Continue

Blog Posts

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Road Trip

Posted by Ray Schick on January 21, 2020 at 9:00pm 7 Comments

Got a little cabin fever this morning,decided to take a road trip to Hickory Corners Michigan, The Gilmore Museum. It’s about 2 1/2 hours from my home . Place is awesome,I was really impressed.

9A648CFF-E965-4CE0-8E91-8E194AC70DED.jpeg…



Continue

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments

37E244B6-71C7-4857-8D50-1BD8C48077A4.jpeg

Looking to buy the choke tube for my Rochester... anybody have one for Sale???

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service