Last minute things when i was cleaning up b4 start.

I was puttingvaway a roch rebuild kit and noticed these two gaskets, they are different.  Other kit i had on rebuild, had two that looked like the one on the right.  I set up carb w two that were on right.  Is that correct or is a mixed version of the two correct? I looked at photos in manual, but none indicate the layout or orientation.

Any thought on this for the rochester 4bbl

Views: 55

Reply to This

Replies to This Discussion

I don't see a photo but most rebuild kits are configured to cover multiple applications. You almost always end up with parts you don't need.


Kim

There is none on the right as one  gasket is over   The other in the photo so pls clarify 

The one on the bottom looks like it goes first on top of the intake manifold due to the front cut outs for the manifold heat passages to warm the carb 

Enjoy 

For reference, this is the one I sell for the Rochester 4GC carb - a Felpro 9770 ... It is the same gasket used below and above the intake manifold to carburetor insulator (I sell the Felpro 60034 for the Carter AFB):

Thanks Jason,

I kinda thought it was the case but wanted to make sure

RSS

Photos

  • Add Photos
  • View All

Forum

Deville

Started by Planet-automobile in Wanted to Buy 3 hours ago. 0 Replies

HiI am looking for a cadillac deville 64 convertible with A/C to restoreabout 10000$if you have any contact meContinue

429 restoration

Started by Matti Roth in Restoration Discussion. Last reply by Tony and Ginny 429 7 hours ago. 6 Replies

Hello, and thanks for adding to group!I am restoring 1964 429 engine which I bought as dismantled. It is said to be smoking in driving and has been stored as parts for a year. It is most probably…Continue

Tags: #429

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 11 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 244 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

63 Trunk detail

Posted by Bob Pontius on April 8, 2021 at 3:07pm 1 Comment

Jason, I liked the detail and information you have provided. I would like to do mine similar to yours. Can you help? Do you have trunk material? OPGI is sending the trunk product for my 63 Fleetwood. But it does cover the entire trunk as yours was done. If you do not have can you give me a reference? Thanks!! Bob

Car lift and jack stands

Posted by Les Eastling on March 23, 2021 at 10:00am 4 Comments

I mentioned during the 63/64 chapter zoom meeting on 3/21 that we had installed a car lift in our garage. Someone asked what kind and I didn't have the info at hand, so here is a link to it and also a link to some tall jack stands we use to add more stability to the car and an additional safety factor. There is something about getting underneath one of these cars that makes me a little nervous! …

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service