Last minute things when i was cleaning up b4 start.

I was puttingvaway a roch rebuild kit and noticed these two gaskets, they are different.  Other kit i had on rebuild, had two that looked like the one on the right.  I set up carb w two that were on right.  Is that correct or is a mixed version of the two correct? I looked at photos in manual, but none indicate the layout or orientation.

Any thought on this for the rochester 4bbl

Views: 58

Reply to This

Replies to This Discussion

I don't see a photo but most rebuild kits are configured to cover multiple applications. You almost always end up with parts you don't need.


Kim

There is none on the right as one  gasket is over   The other in the photo so pls clarify 

The one on the bottom looks like it goes first on top of the intake manifold due to the front cut outs for the manifold heat passages to warm the carb 

Enjoy 

For reference, this is the one I sell for the Rochester 4GC carb - a Felpro 9770 ... It is the same gasket used below and above the intake manifold to carburetor insulator (I sell the Felpro 60034 for the Carter AFB):

Thanks Jason,

I kinda thought it was the case but wanted to make sure

RSS

Photos

  • Add Photos
  • View All

Forum

622 nss 63 tilt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kim K Kaiser 7 hours ago. 5 Replies

Previously, i mentioned the  bu lights didnt work, and conversatiin went to nss.   Mine has the two jumped wire bypass so car will go in drive/start.Got the switch out and the outer tract plastic is…Continue

Timing chain help

Started by Cody in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 21 hours ago. 3 Replies

I have the front of my engine taken apart to replace the timing chain and gears. According to the manual it says to remove the cam gear and chain together then the crank gear.I can’t for the life of…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 22 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Organizing For Sale?

Started by Anders in Suggestion Box. Last reply by Jason Edge yesterday. 1 Reply

Been looking on the For Sale forum. Not sure if possible or not, but it might be good if there would be sub-forums so cars go in one area and maybe spares could be sorted in a way as well. No idea…Continue

Blog Posts

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service