I am look for all 6 pieces of side molding for 1963 series 62 coupe.

Views: 93

Reply to This

Replies to This Discussion

I have several side moldings for a 1964 Deville. Not sure if they are compatible. Jon

Hi Jon,

Could you take a picture of the fender trim where it connects to the front boomerang?  That will tell me if it will fit. Thank you!

Door and rear qtr are interchangable. Front fender side trim is quite different due to larger eyebrow molding it connects with at the front on 63 vs very thin eyebrow trim on the 64, and the raised square ridge down bottom of front fender from wheel well to front on the 63. The 63 trim is physically wider than the 64 as it approaches the front, and the 63 is not side specific while the 64 is due to the fact it taper to a thinner point to meet the thin 64 eyebrow molding. 
So... 63 to 64 Coupe door trim is the same/interchangeable and 63 to 64 Coupe rear qtr is the same/interchangeable, but not the front fender trim. There are also a couple of versions of the rear qtr trim as some have a flattened very end and others have a raised square end... and both types seem to be used on both years.. but just something to be aware of.

Thank you Jason for the information! I appreciate your knowledge!!

Hi Jon,

I am interested in coupe door trim and coupe quarter trim for both sides? 

Hi Jon,

looking for passenger side fender side trim for 64 Deville sedan. Still available?

regards,

Matti

How much

RSS

Photos

  • Add Photos
  • View All

Forum

622 nss 63 tilt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Kim K Kaiser 7 hours ago. 5 Replies

Previously, i mentioned the  bu lights didnt work, and conversatiin went to nss.   Mine has the two jumped wire bypass so car will go in drive/start.Got the switch out and the outer tract plastic is…Continue

Timing chain help

Started by Cody in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 21 hours ago. 3 Replies

I have the front of my engine taken apart to replace the timing chain and gears. According to the manual it says to remove the cam gear and chain together then the crank gear.I can’t for the life of…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 22 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Organizing For Sale?

Started by Anders in Suggestion Box. Last reply by Jason Edge yesterday. 1 Reply

Been looking on the For Sale forum. Not sure if possible or not, but it might be good if there would be sub-forums so cars go in one area and maybe spares could be sorted in a way as well. No idea…Continue

Blog Posts

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service