I am look for all 6 pieces of side molding for 1963 series 62 coupe.

Views: 95

Reply to This

Replies to This Discussion

I have several side moldings for a 1964 Deville. Not sure if they are compatible. Jon

Hi Jon,

Could you take a picture of the fender trim where it connects to the front boomerang?  That will tell me if it will fit. Thank you!

Door and rear qtr are interchangable. Front fender side trim is quite different due to larger eyebrow molding it connects with at the front on 63 vs very thin eyebrow trim on the 64, and the raised square ridge down bottom of front fender from wheel well to front on the 63. The 63 trim is physically wider than the 64 as it approaches the front, and the 63 is not side specific while the 64 is due to the fact it taper to a thinner point to meet the thin 64 eyebrow molding. 
So... 63 to 64 Coupe door trim is the same/interchangeable and 63 to 64 Coupe rear qtr is the same/interchangeable, but not the front fender trim. There are also a couple of versions of the rear qtr trim as some have a flattened very end and others have a raised square end... and both types seem to be used on both years.. but just something to be aware of.

Thank you Jason for the information! I appreciate your knowledge!!

Hi Jon,

I am interested in coupe door trim and coupe quarter trim for both sides? 

Hi Jon,

looking for passenger side fender side trim for 64 Deville sedan. Still available?

regards,

Matti

How much

RSS

Photos

  • Add Photos
  • View All

Forum

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 2 hours ago. 20 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

A Before & After Example

Started by Jason Edge in Restoration Discussion yesterday. 0 Replies

Since I started cadmium plating the many fasteners and other items from the 55 and counting parts cars I have bought in (1200 lbs worth and counting), I have to say it has really taken the…Continue

Oil leaking out of oil cap breather

Started by mark zimmerman in Restoration Discussion. Last reply by mark zimmerman yesterday. 12 Replies

Hi i would like some ideas on this i replaced oil cap breather and pcv valve and still oil  coming out of breather at normal speeds down the road.This has been going on for quiet awhile from the…Continue

Update on fuel pump

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by William R Conte yesterday. 1 Reply

I'm still looking thru land and sea for this fuel pump anyone out there know what size engine I have here are some pics of the stamps on the block I found to make sure my engine is a 390 because the…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service