I am look for all 6 pieces of side molding for 1963 series 62 coupe.

Views: 130

Reply to This

Replies to This Discussion

I have several side moldings for a 1964 Deville. Not sure if they are compatible. Jon

Hi Jon,

Could you take a picture of the fender trim where it connects to the front boomerang?  That will tell me if it will fit. Thank you!

Door and rear qtr are interchangable. Front fender side trim is quite different due to larger eyebrow molding it connects with at the front on 63 vs very thin eyebrow trim on the 64, and the raised square ridge down bottom of front fender from wheel well to front on the 63. The 63 trim is physically wider than the 64 as it approaches the front, and the 63 is not side specific while the 64 is due to the fact it taper to a thinner point to meet the thin 64 eyebrow molding. 
So... 63 to 64 Coupe door trim is the same/interchangeable and 63 to 64 Coupe rear qtr is the same/interchangeable, but not the front fender trim. There are also a couple of versions of the rear qtr trim as some have a flattened very end and others have a raised square end... and both types seem to be used on both years.. but just something to be aware of.

Thank you Jason for the information! I appreciate your knowledge!!

Hi Jon,

I am interested in coupe door trim and coupe quarter trim for both sides? 

Hi Jon,

looking for passenger side fender side trim for 64 Deville sedan. Still available?

regards,

Matti

How much

Let me know what parts you are still interested in. I have  tons of time now. Jon 5613010659

I can help

RSS

Photos

  • Add Photos
  • View All

Forum

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 13 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

You Know You Are Into Some Serious Car Doctor When You Have to Get the Ice Out!

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 17 Replies

You know you are into some serious car doctoring when you have to get the ice packs out. More to come on my 64 Coupe de Ville resuscitation in the next 1963/64 Cadillac Chapter Newsletter!  Mades…Continue

Unknown part, maybe the last one?

Started by Matti Roth in Restoration Discussion. Last reply by Jason Edge yesterday. 1 Reply

Hithanks to great help from chapter members I am getting my 64 Deville ready, slowly but surely.There is only one part still unclear, or actually three bolts and nuts. They are clearly different from…Continue

Leaky Windshield

Started by Tom Bahner in General Discussion. Last reply by Tom Bahner yesterday. 4 Replies

Hey all, has anyone had their windshield removed and resealed successfully. I'm pretty skittish about having someone mess with my perfectly good glass knowing that these cars are a little different…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service