Hello,

Reinstalled motor and trany this weekend in my 63 390 and jetaway after overhauling both. Problem: the torque convertor is about 3/16" away from making contact with the flex plate. When I try to tighten up the flex plate nuts the flex plate flexes or bends.   questions: should the torque convertor have some movement to make contact with the flex plate or is it solid no movement? And does the nose of the torque convertor go into the back of the crank shaft?  I'm thinking the back of my crank is rusty since its not the crank that camo out of the car, stopping the convertor from moving forward.

Thanks for the feed back.

Pete

Views: 90

Reply to This

Replies to This Discussion

Pete 
Are they the engine and trany that were in the car before or was something changed ?

Stay safe 

Are you implying you changed the engines original crankshaft ?

The 1964 Turbo Hydramatic flexplate has a 3" opening. The raised back end of the 1963 390 Hydramatic crankshaft and 1964 429 Hydramatic crankshaft is 3 3/16". The flex plate is not going to fit the Hydramatic crank unless it is enlarged to exactly 3 3/16" and it has to be exactly centered!  It sounds like you are trying to mate a 1964 429 Turbo Hydramatic to a 1963 390 which came with the Hydramatic crank. For more details on this and other issues you will run into check out this help page: Engine and Transmission Facts - differences from 62 to 63 to 64 to 65

Be sure to scan down to the Swapping Transmissions - Things to Consider section.

All 390’s in 63 had  the hydromatic trans 

In 64 the 429 —had two trans  mounted to the engine depending on the model Cadillac in 64 

Two  different crankshafts  size ends —-came in the 429  engine in 64 

One size crank —was for the hydro trans 

A second size crankshaft  in the 429 —came in the engines that got the turbo (400) hydro trans which has a spacer in 64 year only 

The correct engine  must be used  with the correct trans depending on the engines crankshaft   End size and —they are not interchangeable due to the size of the crankshaft end that couples to the trans being different 

This will cause a major complication  in matching the correct engine to the correct trans if not done correctly 

As noted in the above post by Jason then a good number of other issues will have to be addressed 

Dropping a 429 with a hydro trans —that came that way in a given 64 model - would work in any Cadillac in 63 or 64 that originally came with the hydro trans making that swap correct and very much less complicated to get done correctly 

Having  two different crankshaft sizes in the same engine in a given year is completely unique to the 64 429 engine very much complicating a trans swap if not understood clearly 

Stay safe 

Thank you all for the comments. I had to change the engine due to a cracked block. I got an complete 63 390 short block, (thank you Russ). completely rebuilt it, but I failed to clean the rust out of the back of the crank where the nose of the converter slides in. I gave the flywheel a couple love taps with a brass hammer and it moved forward just enough. The convertor must move freely in the back of the crank for ballooning.   

Pete

Glad it was an easy fix. It was ironic the # you used 3/16" which is the exact different in diameter of the 1963 drive plate and 1964 flexplate.

Glad it turned out to be a simple issue that you worked thru 

Always the best case scenario 

Enjoy having your car back in action 

Stay Safe 

RSS

Photos

  • Add Photos
  • View All

Forum

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 13 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

You Know You Are Into Some Serious Car Doctor When You Have to Get the Ice Out!

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 17 Replies

You know you are into some serious car doctoring when you have to get the ice packs out. More to come on my 64 Coupe de Ville resuscitation in the next 1963/64 Cadillac Chapter Newsletter!  Mades…Continue

Unknown part, maybe the last one?

Started by Matti Roth in Restoration Discussion. Last reply by Jason Edge yesterday. 1 Reply

Hithanks to great help from chapter members I am getting my 64 Deville ready, slowly but surely.There is only one part still unclear, or actually three bolts and nuts. They are clearly different from…Continue

Leaky Windshield

Started by Tom Bahner in General Discussion. Last reply by Tom Bahner yesterday. 4 Replies

Hey all, has anyone had their windshield removed and resealed successfully. I'm pretty skittish about having someone mess with my perfectly good glass knowing that these cars are a little different…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service