Hello All,

Took the car in for front end alignment and car remains at facility. The tech drove the car into bay and returned it to the same spot that I drove into. Paid for work and was ready to drive home: when I got in the driver seat noticed the gear shifter was not in park position, but down in reverse "R". Tried to move it up to proper position to start and get out of there. Nothing doing could only get the shifter to go to drive "D", no further. Stormed back into the office and asked when were they planning on telling me the tech broke something on my car. Argruments and alot of finger pointing and I left the car for them to figure how they would like to handle the issue. The car is a 6200 series, 1963 has anyone else ever had this type of issue or know anyway that it can be resolved. I do know at some point I will have to assist them in getting the car taken care of. Any help will be gladly appreciated.

Views: 313

Reply to This

Replies to This Discussion

Maybe check the shift linkage  , check the neutral safety switch on column,  get under the car and inspect trans linkage . If you drove the car to the shop and it was fine ,that’s the only thing I can think of at the moment  

Just returned from the shop one of the helpers told me he dismantled the linkage and the shifter in the vehicle was able to move freely. cars rolls forward and backwards so he imagines it is in neutral??? The aparatus where the linkage connects on the side of the transmission he did think that it was turning around 360 degrees when the linkage was disconnected; but he was'nt 100% sure.

Will neutral safety switch keep the car from shifting into gear?? Maybe somehow technician kicked it by mistake??? Hopefully this extra info helps.

Thanks,

If the transmission shift lever can spin 360 degrees, then you might have a stripped out detent lever or stripped manual shaft in the transmission.    Just as likely, the set screw has come undone and slipped off the end somehow.    If the detent is still attached to the lever, there is no way it would have room to turn all the way around, so the shaft is spinning independently inside of it.  Remove the pan and you'll see it immediately.  

If there are no detents(clicks) in the trans linkage, there is no way of telling what gear it's in.  You can only tell when it is in park by rolling it, an automatic trans is always in neutral when the engine is off.   You can find out what gear it's in only by starting the engine, but by no means should you try to drive it with the manual valve linkage in an unknown place.   If the linkage is spinning freely, you could be between gears, like halfway between neutral and drive, and driving it in that position will be driving with reduced hydraulic pressure, which can VERY quickly burn out clutches from slippage.    
The NSS won't make the car not shift unless it falls apart and somehow gets lodged in the shift tube in the column.  You can't kick it that hard, as I could imagine, unless your mechanic is a rodeo bull.

Thanks Much Ray!!!

The guy who dismanteled the  trans linkage caused the problem 

I would think it is not reinstalled correctly and SB inspected and adjusted to work correctly again 

Just my best guess 

Enjoy 

Mark & Tony, Many Thanks

If you went in for front end work what was this mechanic doing playing with your trans linkage ?

One has nothing to do with the other 

Why did he have a need to go there ?

Enjoy 

Any pictures of the trans linkage - of the trans in a 6200 series 1963  Cadillac available to view ?

Enjoy 

Tony I have not a clue?? I wasn't watching, but I really believe something went wrong on the lift when they were giving it an inspection to find other avenues to try and extract money from my wallet.....

No original pics under the car - but it does look identical to what is in the Cadillac Shop Manual for the year.

Examine the linkage at the bottom of the steering column -that is under the hood just below the brake booster area 

A lot of the steering linkage is located there  that changes the trans gears when you use the steering column lever to change gears when in the driver seat 

Enjoy 

The last post should read ——-a lot of trans linkage is located there ( not steering ) 

Enjoy 

I did see a collar with a spring underneath it, also a lever came out that was attached to another linkage lever of some sort, Wasn't familiar with it at all but did wonder if it needed lubrication of some sort to help it's movement. Tony are we speaking of the same part??

RSS

Photos

  • Add Photos
  • View All

Forum

1964 Interior AC/Heater Box Removal

Started by Travis in Restoration Discussion. Last reply by Travis 6 hours ago. 13 Replies

Newby question here!  I've read through the shop manual and as many threads as I could find on here, but I'm still stumped on exactly how to remove the interior plastic Heater/AC box from my 64 SDV…Continue

Tags: vacuum, mode, door, box, a/c

What gasket or seal at the PCV pipe under intake?

Started by Tosh Dickenson in General Discussion. Last reply by Tosh Dickenson 12 hours ago. 2 Replies

Wonder what kind of seal goes on the metal PCV pipe under the intake?  It looks like the larger part is kind of a press fit into the manifold but maybe there was a rubber gasket under the bolt that…Continue

Ordering Polyurethane Replacement Trailing Arm Bushings

Started by Dan McNarry in 1963/64 Cadillac Specific Discussion. Last reply by Dan McNarry 12 hours ago. 3 Replies

There seems to be growing interest in the poly bushings. In order for me to keep track of who wants bushings, please send me a message along with or in lieu of a reply to either this thread or the…Continue

Drain plug and speedo bullet seal.

Started by Pete Grodem in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin 17 hours ago. 3 Replies

Hello,Sealing  up my 63 Jetaway duel coupling and questioning the drain plug and the speedo bullet, both used an o ring for sealing. This does not seam proper as the o ring gets crushed when…Continue

Blog Posts

How to sensibly deal with the Corona Virus

Posted by Jeff Kinzler on March 14, 2020 at 5:02pm 6 Comments

https://theamericanscholar.org/covid-19-a-primer/

I found this very helpful, written by a knowledgeable authority in public health. 

Remember, Viruses are not spread by Cadillacs so get out and drive!


Safe & Healthy travels. 

Jeff Kinzler

1963 Eldorado convertible boot

Posted by Les Eastling on February 27, 2020 at 10:33am 1 Comment

I need a used convertible boot for a 63 Cadillac convertible - condition or color is not an issue since it will be used as a pattern for making a new one. One from either a 62 series convertible or an Eldorado would work. I know I am searching for hen's teeth here... but you never know unless you ask!

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service