Hello All,

Took the car in for front end alignment and car remains at facility. The tech drove the car into bay and returned it to the same spot that I drove into. Paid for work and was ready to drive home: when I got in the driver seat noticed the gear shifter was not in park position, but down in reverse "R". Tried to move it up to proper position to start and get out of there. Nothing doing could only get the shifter to go to drive "D", no further. Stormed back into the office and asked when were they planning on telling me the tech broke something on my car. Argruments and alot of finger pointing and I left the car for them to figure how they would like to handle the issue. The car is a 6200 series, 1963 has anyone else ever had this type of issue or know anyway that it can be resolved. I do know at some point I will have to assist them in getting the car taken care of. Any help will be gladly appreciated.

Views: 330

Reply to This

Replies to This Discussion

Glad I can help Ron .

Find out where the lever ——that came out —looks like it belongs 

Hold it in place any way you might 

Reattach it where it looks like it belongs  if possible and see if that helps to correct your finding a correct gear issue on the column 

Enjoy 

Anything positive going on with the gear shift problem ?

Enjoy

Hey Tony!!,

I filed claim with Firestone Corporate, did not want to deal with local or regional. Seemed to me they were trying to wash their hands of the problem and put everything back on me. I speak to a claims specialist tomorow. Once we get it to tranny shop will pass along all the pertinent information to them should they need it. Just horribly madd and upset, something so simple gone so bad!! Keep you all posted

Many Thanks,

Hello All,

Took the car to one of the premier Caddy dismantlers and service departments in my area. Mark was right on point with the part that needs to be replaced the "inside detent control and set screw" along with the "detent spring and roller assembly and attaching screw" on the inside of the tranny. Now that we have the parts targeted and know what we need; we are having trouble locating them so the saga continues. Thanks for all the support along the way the information saved a ton of labor time narrowing down the problem. Hopefully can track down the parts and have a good long cruise before sumer ends!!

Ron

There are a couple of good parts guys posting here who must have a core hydramatic sitting around, so you've got a good shot at getting what you need easily.   These are simple parts to remove, just a little messy to open the pan.
The roller detent spring is still available, I'm pretty sure, from Fatsco transmission parts in New Jersey (they're awesome, btw).  They may also have the detent assembly, but I never needed one so I can't say they do.

You're very lucky if it didn't knock the end off of the manual valve when it broke.  That would require dropping the valve body, and a lot more parts scrounging and expense.

I took a car to an upholstery shop for some interior work.  When I went to pick it up, the shifter wouldn't find a detent to stay in gear.  The detent spring and roller broke, and it had nothing to do with the shop.  Sounds like the same thing with you. cant be blaming a shop for a 50 plus year old part breaking on them.

On a good note, I should have the detent roller.  Send me an email to  russ85747@hotmail.com 

Russ is surely the bottom line  right answer to this broken shifter issue especially having had the same experience himself 

Always glad that man is on this site for years 

Never heard of the those parts before but good to know  it’s not to bad a repair to attack 

Enjoy 

Do let Russ help you acquire your parts 

Enjoy 

From a current thread regarding a trans gasket replacement on the site  right now 

The hardest part of replacing the parts for the shift lever detent —would be to get the pan gasket back on and not leak 

Perfect time to address trans filter needs and new fresh trans fluid 

Trans all better and prepped for the long haul 

Ron enjoy getting the car back and enjoying it again 

Enjoy 

Thanks Tony,

I was reading the threads on the tranny pan gasket!! Guess that's why there was 17 pounds of RTV caked all around the pan. Gonna be Fun!!

 Ron 

very glad you are getting  very close to getting back to driving your pride and joy again 

Enjoyed learning some very good info from this thread 

Always a FUN thing for me regarding my passion for  any and all knowledge regarding our year cars 

the joy my 64 Convertible has brought to my life  for 55 years is simply priceless for this confirmed Gear head 

Enjoy 

Enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

Rear Wheel Bearings Replacement

Started by Dominic Salemi in 1963/64 Cadillac Specific Discussion 23 minutes ago. 0 Replies

HiNeed to replace my rear wheel bearing and seal on my 1964 Conv., does anyone know if its a big project and what I will need before I pull the shaft out? I also need to know the parts number and…Continue

Winter time cruise in Australia.

Started by Kevin Campbell in General Discussion. Last reply by Kevin Campbell 28 minutes ago. 4 Replies

The weather here in winter is great for a Cadillac cruise.Continue

looking for a 429 heat riser and cruise control unit

Started by Christian Doerk in Wanted to Buy. Last reply by Kurt 1 hour ago. 1 Reply

I am looking for a functioning heat riser valve and a cruise control for a 1964 Cadillac.In principle, the heat riser flap does not have to work. It is only important that the spacer / housing is not…Continue

Tags: exhaust, riser, heat, control, cruise

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 2 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

64 Power Servo vacuum leak

Posted by Kent Prows on June 27, 2020 at 4:02pm 0 Comments

I finally got around to fixing a leak in my heater core.  I decided to check to see if there were any other obvious issues while I had everything torn apart.  When I put a vacuum directly (bypassing the transducer) to the power servo it gets to about 10" and then slowly leaks back to zero.  The fan will not go to full and the mode door will not open completely.  I have read a couple of other posts that said they repaired the power servo leaks.  How?  Does anyone have one to sell?  I just…

Continue

63 Caddy Horn

Posted by Robert Alan Shannon on May 27, 2020 at 9:25am 9 Comments

 Just noticed a 1963  Caddy trumpet horn on Ebay. No part # given but some of his other items are 1963 specific, just throwin this out there, I have no connection to this listing .

Wiring connection help.

Posted by Jimmy Davis on May 24, 2020 at 9:15pm 2 Comments

Can someone help me figure where these connections go? I have a 64 60 special if it matters.…



Continue

Wood grain finally done.

Posted by Jimmy Davis on May 20, 2020 at 4:57pm 3 Comments

After years of wanting to, I finally redid my wood dash paneling on my 64 60s. Not too hard to do either.…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service