After finding leak arpund rim of trans pan.  I ordered a gasket.  

I was checking to see if there are any pitfalls or suggestions to getting it right.

I assume drain pan from the drain bolt, then pull the pan and replace.  Will anything drop or fall from the underside of the pan on removal that i should be concerned with.

Views: 213

Reply to This

Replies to This Discussion

nothing should drop.

check it for flatness while it's out, people overtorque them and they pucker at the bolt holes.
to flatten it, put the flange on a piece of wood and lightly tap the bolt holes till there is little or no gap when checking with a straight edge

ok,, thanks for the information,,   i will give it a go...

i got the pan off and cleaned it up,, the old gasket took some time to get off the pan.  everything looked clean and covered with dripping transmission fluid..i cleaned up the pan real good with no dirt or debris nd put the pan back on before the darkness got me..

i checked the manual for true on those bolts and it said a 5/16 at 18 lbs.  well, mine had 1/2 bolt, and it said the drain was 40 lbs.. 

so i became confused as to whether 18 lbs was correct so i thought i would ask to make sure i got the right torque figures.. 

what would the torque for the bolts be, and is the drain plug at 40??

Ugh.  I think i got it.  The 5.16 bolt is the shaft size not the head size.

Just make the drain plug reasonably tight and be sure it’s not leaking

Enjoy  

well, i replaced the gasket,  and dumb ass me, read the wrong listing for bolt tongue,, i found the drain plug torque of 40, and the entry right above.. said 13,, that was the day before i put the pan back on.. so, next day, i went back and looked again, and read the wrong dam entry and it said 18,, so i put 18 in,, well you guessed it, it crushed the gasket,, so, back to oreilly,,  got new ones coming tomorrow with 13 currently embedded in my head... 

on a good note, so far, the replaced valve covers are not leaking as of now as of the change the other day..  and the fuel pump back bolt doesnt seem to be leaking anymore as well after pulling it and putting some gasket seal on the threads and putting back in.. so hopefully, two minor seepages are tackled.. .... i say with fingers crossed

for me  2 outta 3  is pretty good,, bak to the pan tomorrow

Carpenter's say "Measure twice, cut once". Mechanics might say "Read twice, torque once!" Perhaps, you should add a step "Read twice, write it down, torque once!" With that I am surprised 18 inch/lbs crushed the gasket. That is only 1.5 ft lbs.  I could see 5, 10 or maybe 18 ft lbs crushing the gaskets, but 18 inch/lbs should absorb that torque .. I would think.  I would make double sure you are reading and setting your torque wrench correctly.  

Well,  i kinda thought inch pounds but it says ft lbs at top of column.  Or, am i reading the chart wrong,  its under the hydra matic transmission chapter.  Attaching photo to verify

book photo of torque,, am i looking at the right entry??

Attachments:

That is 13 ft lbs. You stated "18 in" and I read that as 18 inch lbs and thought you were referring to inches. When the shop manual lists inch lbs (e.g. the valve covers) it will specifically state inches. So yes, 18 ft lbs could crush the gasket when it should be 13 ft lbs. As I had stated in another thread, you want to gradually increase the torque. For 13 ft lbs I would torque to 5 ft lbs, then 10 ft lbs then 13 ft lbs using a back and forth torque pattern.   

ok,, good,, I'm sorry for the typo that confused your answer and understanding,i guess iw as thinking i was putting 18 lbs in the torque wrench,, so again, sorry for that confusion., but i am glad that i am on the right page and the right items,,,,thanks again for re reading and setting me strait,,,,,i will get this figured out one day,, 

Quick question on transmissuon pan.  I got off for second time,  looked were leaks came from.  And was looking to see if pan flatt.  

Should all the bolt holes have a little rise or should the be flat flush w the flat surface,

The re leak occured at the split gasket, felt like that was good reason for leak.  But other one was were it leaked before. Front right corner,  so,  do i need to flatten bolt holes for uniform flat surfacr all the way around?

RSS

Photos

  • Add Photos
  • View All

Forum

New photo gallery

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 1 hour ago. 8 Replies

Having trouble posting my picture in the new gallery but managed to get the text right The computer WIZ - I am NOT ! Stay safe my friends Continue

New Car Gallery Page Created - Post a Picture of your 1963/64 Cadllac

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 2 hours ago. 4 Replies

Hello 63/64 Cadillac Website Members,Hope you are all staying safe amid the Coronavirus shutdown and wanted to share something new & fun on the 63/64 Cadllac Website at…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 3 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

1963 coupe deville front relocation shock kit

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Jason A 12 hours ago. 6 Replies

Howdy everyone had a question maybie you guys can help me,I have a 1963 coupe deville and i got it with air bags problem is its way to bouncy in the front need to get a shock relocatio ok n kit but I…Continue

Blog Posts

How to sensibly deal with the Corona Virus

Posted by Jeff Kinzler on March 14, 2020 at 5:02pm 6 Comments

https://theamericanscholar.org/covid-19-a-primer/

I found this very helpful, written by a knowledgeable authority in public health. 

Remember, Viruses are not spread by Cadillacs so get out and drive!


Safe & Healthy travels. 

Jeff Kinzler

1963 Eldorado convertible boot

Posted by Les Eastling on February 27, 2020 at 10:33am 1 Comment

I need a used convertible boot for a 63 Cadillac convertible - condition or color is not an issue since it will be used as a pattern for making a new one. One from either a 62 series convertible or an Eldorado would work. I know I am searching for hen's teeth here... but you never know unless you ask!

Looking for 63 Convertible / Coupe rear side trim

Posted by Gene McIlroy on January 24, 2020 at 12:18pm 0 Comments

Want to find a good straight dent free rear side trim for my 1963 Convertible.  I have both sides but they do not match.  Wanting to get them to match.  I am attaching a photo of the two trim sided that I have really wanting the squared off trim if I can get it.  Let's see what you have,…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service