After finding leak arpund rim of trans pan.  I ordered a gasket.  

I was checking to see if there are any pitfalls or suggestions to getting it right.

I assume drain pan from the drain bolt, then pull the pan and replace.  Will anything drop or fall from the underside of the pan on removal that i should be concerned with.

Views: 181

Reply to This

Replies to This Discussion

nothing should drop.

check it for flatness while it's out, people overtorque them and they pucker at the bolt holes.
to flatten it, put the flange on a piece of wood and lightly tap the bolt holes till there is little or no gap when checking with a straight edge

ok,, thanks for the information,,   i will give it a go...

i got the pan off and cleaned it up,, the old gasket took some time to get off the pan.  everything looked clean and covered with dripping transmission fluid..i cleaned up the pan real good with no dirt or debris nd put the pan back on before the darkness got me..

i checked the manual for true on those bolts and it said a 5/16 at 18 lbs.  well, mine had 1/2 bolt, and it said the drain was 40 lbs.. 

so i became confused as to whether 18 lbs was correct so i thought i would ask to make sure i got the right torque figures.. 

what would the torque for the bolts be, and is the drain plug at 40??

Ugh.  I think i got it.  The 5.16 bolt is the shaft size not the head size.

Just make the drain plug reasonably tight and be sure it’s not leaking

Enjoy  

well, i replaced the gasket,  and dumb ass me, read the wrong listing for bolt tongue,, i found the drain plug torque of 40, and the entry right above.. said 13,, that was the day before i put the pan back on.. so, next day, i went back and looked again, and read the wrong dam entry and it said 18,, so i put 18 in,, well you guessed it, it crushed the gasket,, so, back to oreilly,,  got new ones coming tomorrow with 13 currently embedded in my head... 

on a good note, so far, the replaced valve covers are not leaking as of now as of the change the other day..  and the fuel pump back bolt doesnt seem to be leaking anymore as well after pulling it and putting some gasket seal on the threads and putting back in.. so hopefully, two minor seepages are tackled.. .... i say with fingers crossed

for me  2 outta 3  is pretty good,, bak to the pan tomorrow

Carpenter's say "Measure twice, cut once". Mechanics might say "Read twice, torque once!" Perhaps, you should add a step "Read twice, write it down, torque once!" With that I am surprised 18 inch/lbs crushed the gasket. That is only 1.5 ft lbs.  I could see 5, 10 or maybe 18 ft lbs crushing the gaskets, but 18 inch/lbs should absorb that torque .. I would think.  I would make double sure you are reading and setting your torque wrench correctly.  

Well,  i kinda thought inch pounds but it says ft lbs at top of column.  Or, am i reading the chart wrong,  its under the hydra matic transmission chapter.  Attaching photo to verify

book photo of torque,, am i looking at the right entry??

Attachments:

That is 13 ft lbs. You stated "18 in" and I read that as 18 inch lbs and thought you were referring to inches. When the shop manual lists inch lbs (e.g. the valve covers) it will specifically state inches. So yes, 18 ft lbs could crush the gasket when it should be 13 ft lbs. As I had stated in another thread, you want to gradually increase the torque. For 13 ft lbs I would torque to 5 ft lbs, then 10 ft lbs then 13 ft lbs using a back and forth torque pattern.   

ok,, good,, I'm sorry for the typo that confused your answer and understanding,i guess iw as thinking i was putting 18 lbs in the torque wrench,, so again, sorry for that confusion., but i am glad that i am on the right page and the right items,,,,thanks again for re reading and setting me strait,,,,,i will get this figured out one day,, 

Quick question on transmissuon pan.  I got off for second time,  looked were leaks came from.  And was looking to see if pan flatt.  

Should all the bolt holes have a little rise or should the be flat flush w the flat surface,

The re leak occured at the split gasket, felt like that was good reason for leak.  But other one was were it leaked before. Front right corner,  so,  do i need to flatten bolt holes for uniform flat surfacr all the way around?

RSS

Photos

  • Add Photos
  • View All

Forum

I need to buy rim for tire Los Angeles ca

Started by Charles in Wanted to Buy. Last reply by Ian Osborne 2 hours ago. 1 Reply

in need or rim for tire Cadillac Fleetwood 64 any one known why i can buy in Los Angeles ca ..hi..thanks 310 309 0332Continue

Hydra-Matic with some problems

Started by Robert Tor in 1963/64 Cadillac Specific Discussion. Last reply by Robert Tor 3 hours ago. 8 Replies

today was a black saturday: my 1964 Caddy "baby" only drives in the first gear and reverse. so I drained the oil (6 liters - not drained the converter) , pulled off the pan and the filter. just dirt…Continue

Rear main Follow up replacement and repair,,

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 4 hours ago. 18 Replies

Well, got it all together,, Jason, i was looking in the wrong chapter in the manual on the starter,, got that figured out.  everything hooked back upGot it put back together, started up, and oil…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 7 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Carter AFB carburetor question

Posted by Ray Schick on October 7, 2019 at 8:29pm 8 Comments

3655S carb, and a 3656S carb .I know the difference is one is for A/C and the other in for a non A/C car . Now the question is : can I use the carb bowl from the A/C car on the non A/C car ? They look the same set up next to each other

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service