Hi all

here are some more parts from under the hood to identify

number 1 is two clamps

number 2: 2 bolts, different threads at each end

number 3 is bracket with cadillac blue paint

good luck!

Views: 72

Attachments:

Reply to This

Replies to This Discussion

OK. I'll have a go. 1st Picture are the dehydrator (dryer) clamps taht hold it against the radiator support. You would also have 2 screw that go into two U nuts. Here is a pic:

2nd picture includes 2 of the 4 inner intake manifold fasteners sets. These 3/8" studs are 16 thread on one end and 24 thread on the top end where nut attached. Here is a picture:

3rd picture is the carburetor throttle return bracket and an outer intake manifold to cylinder head bolt. This attached at left rear of engine see picture below:

Thanks! Photos are great help. Pic 2: I found out that 2 studs are still in heads, and I found a nut for one of them. Two washers more were found as well so I have all 4 pcs. I found several bolts which could be used for the corners of intake manifold. There is no space for such big washers like with studs.

Matti 

In the last photo you can see the ground strap from the valve cover to the firewall that you asked about the first time 

Enjoy 

RSS

Photos

  • Add Photos
  • View All

Forum

Rear main seal. 63

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 10 hours ago. 3 Replies

My rms is leaking again.  I hv cked all other options for leaks and its none of those.  Ie, oil presdure, valve covers, etc.  So i called egge to order another one.  I asked the guy wat contack…Continue

Selling 1964 Coupe Deville Parts

Started by Gary Smiley in For Sale. Last reply by Gary Smiley 11 hours ago. 2 Replies

What I  have are many extra original, hard-to-find 1964 Cadillac Coupe Deville Parts (from donor car).…Continue

Tags: doors, hood, engine

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 18 hours ago. 275 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service