what is the vacuum canister for that is behind the drivers front fender?

After removing my fender I see its got a hole in the top but nothing is hooked to it and no line is laying there.

Any help would be great. I finally bought my dream car and starting the process of collecting parts and information.

Walt

Views: 346

Reply to This

Replies to This Discussion

The shop manual shows the power door locks vacuum diagram.  It shows that the "red" hose is "T" to both the left and right front door.  Where is this "T" located?

Rob

Looks like the T fitting is directly behind the dash maybe 6" or so past the firewall. See picture. If you have the original vacuum lines you should be able to trace it. If making up to install in a car that did not have vacuum you might consider a good old used hose set as a guide. Here is the picture ...click to enlarge and note green arrow pointing to T area for vacuum supply left and right. 

If I am reading your picture correctly, the hose on the left of the picture goes to the passenger side door, and the "T" where the green arrow is looks to be on the drivers side about above the radio.  Am I correct?  Where does the other side of the "T" attach to?  I am trying to replace the hoses that run through the drivers side door.

Rob

RSS

Photos

  • Add Photos
  • View All

Forum

Web site up with a new design.

Started by Russ Austin in General Discussion. Last reply by Russ Austin 19 hours ago. 2 Replies

My web site has been down for a few months and I migrated to GoDaddy.com  Best move ever!My new web site rocks, hope you enjoy it.  …Continue

Had the 64 convert out for some Cruising around the town

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 5 Replies

It is 74 degrees sunny and dry in central Fl - what a day !! - Top Down of coarse The usual OOH’S and AH’S people encircling the car when parked -  a NICE yelling from a car  —and a what year is that…Continue

The 64 - 429 Cadillac gas engine —-is a special unique torque monster ! !

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies

The 64 Cadillac gas engine is a torque monster —with 480 ft lbs of toque at 3000 RPMs Out of curiosity I looked up my 409 dual quad  425 HP  race engines   specs and it has only 425 ft lbs of torque…Continue

Blog Posts

Oil pump

Posted by Ray Schick on October 30, 2022 at 4:34pm 4 Comments

I removed the front cover to change out the timing chain & gears all that went pretty well when I put the cover back on I put in a fresh oil filter ,filled it up figured it would be enough to prime the oil pump when I started the car .Fired up the car and heard lifters rattling, So I shut the car down right away. So I removed the oil filter housing, and poured oil down the neck of the oil pump housing filled it up and filled up the filter put it all together and fired it up and same…

Continue

Available parts

Posted by Thomas Reichenberger on October 13, 2022 at 11:47pm 0 Comments

Caddy members, I’m upgrading my 64 2-door coupe deville.

motor guy lost my block (machine shop went under) so I’m replacing motor & tranny with LS conversion. I have motor parts (other than block) for 429, rebuilt transmission, converter, and too many other motor parts not needed with fully dressed LS going in.

Email me (Tom.reichenberger@ipsper.com) or call me (210-739-4854) if you’re interested…..I live in San Antonio, TX.

thanks, TX…

Continue

Trunk Open and Lock Mechanism is in Closed Position

Posted by Chris Anderson on September 13, 2022 at 7:14pm 7 Comments

While working on my trunk lock on 64 Cadillac, I mistakenly closed the locking mechanism while the trunk was open.  Is there an easy way to manually release the lock back to the open position?

Thanks.

Fuel Pump Failure

Posted by Jon Shields on August 6, 2022 at 6:48am 4 Comments

Hello,

I'm located in Melbourne, Australia and my 64 sedan de ville is stuck in the garage due to failed mechanical fuel pump. The first after market mechanical fuel pump lasted a few years before it failed & left me stranded 5 hours from home. A hire car and tow got us home. On inspection, I noticed a valve not seated within the housing. I was optimistic, pressed it into place and assumed the pump was good to go. But alas, no. From what I can now determine, the diaphragm pushrod…

Continue

Videos

  • Add Videos
  • View All

© 2022   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service