Hello!

I am rebuilding 429 for 64 DeVille and got Felpro head gasket kit including valve stem seals. Is it recommended to install those even though they are not originally used? O-rings will be installed of course.

thanks in advance!

Views: 52

Attachments:

Reply to This

Replies to This Discussion

Hi Matti,

Yes its recommended. If you are able to read Swedish you can get additional information from TA Motor (best Company for Cadillac parts in Sweden).

Tack Anders! Jag har redan köpt ganska mycket från TA.

These kids today, I don't understand a word they say!

Matti

Always best to use valve stem seals as they prevent oil being sucked into the cylinders between the valve stem and valve guides ( especially intake valves ) 

This is often done by a machine shop when refreshing the heads as all the valve springs must be removed to install the valve stem seals at the top of the valve guides 

The best valve stem seals I know are —PC Seals —as the top of the valve guide is cut by a machine shop to be installing those which are used in high performance race engines for there positive qualities 

Always be very sure to be installing your rocker arms correctly as some of the best professional engine building shops have installed them wrong on newly rebuilt engines preventing proper oil flow to the heads —-on the ever so important —First break in run to seat the new engines metal parts 

That first engine break in run will determine the condition of  the new engines performance and  longevity for the long haul so very important to get  that right  the first time 

Enjoy 

Thanks!

I am rebuilding it all by myself, with shop manual and other instructions. I have all the time in the world to get it right. 
I am using original cam, crank, pistons, lifters, push rods, block, heads, valves, rocker arms. I need to replace 3 valves and 4 rocker arms only. Plus oil pump gears.  New rings of course. Do I still need to do the break in run?

The break in run is the first 30 minutes the engine runs  for the first time to be polishing all metal to metal surfaces so that they form a smooth  shinny surface between those metals for the life of the engine 

Mostly it is about setting up the engine to fire up as quickly as is possible and then run the engine over 1000 RPMs for 30 minutes non stop and getting the engine to operating temp 

After that run up you will need to re-torque all bolts to  the engines manuals  specs 

Then removing any bugs that pop up like leaking hoses — etc 

A very important procedure fir engine longevity and very much required 

Enjoy 

My concern is if the valve stem seals stay in the valve guides because they were not there originally. Are those 429 valve guides designed to keep stem seals in place?
If seals get loose they could create problems under rocker cover. I wonder if anyone in this group has added them.

RSS

Photos

  • Add Photos
  • View All

Forum

Chapter Member? Got a 63 or 64 Cadillac for Sale? Let's Run it in the Newsletter!

Started by Jason Edge in For Sale. Last reply by Jason Edge 4 hours ago. 4 Replies

One of the new features of recent newsletters is a Member Classified Cars for Sale section.…Continue

vacuum canister

Started by Walt Timmerman in General Discussion. Last reply by Rob Shatsnider 9 hours ago. 15 Replies

what is the vacuum canister for that is behind the drivers front fender?After removing my fender I see its got a hole in the top but nothing is hooked to it and no line is laying there.Any help would…Continue

New Batch of Embroidered Iron-On 1963/64 Cadillac Chapter Patches - $4 each

Started by Jason Edge in Chapter Discussion. Last reply by mark zimmerman 14 hours ago. 10 Replies

As noted in our August 1963/64 Cadillac Chapter Newsletter:Around 6 years…Continue

Tags: Available, Patches, Chapter, Cadillac, 1963/64

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Daniel Grande 22 hours ago. 9 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

Blog Posts

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service