In the last week or two, I've been noticing that when pulling up to stop light (low RPM) my headlights dim slightly, as do the instrument panel lights.   I suspected that I should replace my voltage regulator, which I did today.  15 minute job.  No big deal.

However, when I started the car, at idle, the GEN light came on and stayed on until I pressed on the accelerator just a bit and the GEN light went off, and stayed off as I drove the car.  

As I approached a stop light, when the RMPs dropped off, the GEN light came on again.  When the light changed and I started to accelerate, the GEN light went off.  The cycle repeated itself.

So, because the wife doesn't know how look it takes to change the voltage regulator :-D, I drove over to the nearby auto parts store, bought a new alternator (I figured because why not..perhaps the old one was beginning to fail), and installed a new one.

When I started the car, the same thing with the GEN light continued:  idle = GEN light.  increasing the RPMs = NO GEN light.    And, it appears the headlights at low RPM dim even more than before I changed the Voltage Regulator and the alternator.   UGG!

I checked the ground on the voltage regulator and the ground appears to be solid.

The only thing I did not change in this circuit was what appears to be a variable resistor of some sort??? See below with the ARROW.  

Any thoughts about what might be going on????  Could it be that the new voltage regulator I installed is bad?


Views: 104

Reply to This

Replies to This Discussion

Here it is with the new voltage regulator.   As I consider (obsess) this problem, it seems to me it either has to be this, the ground, or a bad voltage regulator, no?

Here’s a video of the problem.  Also, should ‘t the GEN light be on when the ignition key is in the ACC (eg radio only) position?

Of course it could be that your voltage regulator is bad, but the only information you have is that the gen light is on.  check the voltage at the battery, and take the battery cables off to see if the engine stalls (b.s. shadetree mechanic alternator test)
is the regulator an oem model with adjustable points?  they can be adjusted
what RPM is your idle?
what about the battery ground to the frame, then from frame to body and frame to engine?  
is it a chinese solid state regulator?  i have one that had the light come on even when the battery was charging because it didn't have the large gen light resistor on it and i had to add it on.

it won't be the condenser on the side of the regulator in the pic usually, but you should try unmounting it from the body and letting it hang.  if the problem goes away, it's shorted.  
then you have to see if you can adjust the regulator points after a few voltage drop tests on the ignition harness with the system running.  also check to be sure the alternator is grounded.  Finally you could have a burnt wire on your ignition switch which is lowering voltage to the regulator

Thanks Mark.   I’ll give it a shot.


Some great tips offered 


I put the old voltage regulator back on and the GEN light has gone off and I’m no longer having the problem.  Go figure.

i’m certain I need a new voltage regulator as the head lights are flickering and dimming slightly at low RPM.

I inspected the black ground wire from the alternator to the voltage regulator and it’s old and the plastic coating broken in several place.  I was considering running a new ground wire and trying out the new voltage regulator again. 
Of course, I could throw in the towel and take the car into my mechanic, but what’s the fun in that?


In most cases just cleaning the grounds on the voltage regulator and removing the terminals in its harness and polishing them will get it working as it should again 

You need to be sliding a flat tool in the harness connectors  to be releasing the individual connectors ( release the metal  bippy there - if you will ) 

That fix  worked in the past for both Jason and myself —-with your same issue 

I think in your case just removing and replacing it must have made a better ground connection and it is now working as it should 

The Gen light will always come on for moments  and then go out —-when the car is started and the RPMs are first low then increase 

When  the Gen light is working correctly—a  low idle RPMs will keep it on —until the RPMs are increased and the light will go out — always comes on for a few seconds when started —-just normal if you idle RPM is correct 

If the Gen light keeps coming on at an idle — your idle is to low 

There is a fuse housing on the passenger wheel well —for the Gen light just so you know —for the future 

With our year Cadillacs the first thing to do with any electrical problem —-is ALWAYS -  to be cleaning the grounds involved and 98% of the time that will fix the problem 

Ground connections get intermittent and build resistance  due to cars age 

Do clean the negative battery cable to the frame —under the battery tray to shinny metal —as that is the Mother ground connection 

Get the regulator connections cleaned up and you should be good to go —- Fixed ! 

I would keep the old regulator and a new alternator is always a good thing for future long term  performance 

At an idle-  on a volt meter -  you should be putting out 14 volts —at the battery when the charging system is working correctly 

Love the easy cheep ( no parts ) fixes myself—- always 

You and me have an obligation —-to be keeping your outstanding restoration rolling down the road so you and all others around you can enjoy your great  64 Classic Antique Cadillac ( ICONIC ! ! )

Keep an eye out for any—  Loose  NUTS—. ( and wiring ) as I recently had to do with my Starter solenoid ——HA - HA !! 




  • Add Photos
  • View All


Dino Waiting on Battery!

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Doug Meloan 14 minutes ago. 3 Replies

This past Tuesday I realized I had not cranked Dino, my 64 CDV in a few…Continue

Tags: replacement, battery

People and our year Cadillacs

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by C. Van Tune yesterday. 1 Reply

So I am doing 5 miles an hour in a parking lot As the window of a car going the other way—-  passes  by my drivers  window the guy yells 61  loud !! —-( some what surprising me so loud ) ———and I…Continue

intake manifold gasket from olsen

Started by austin Rock in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 on Friday. 3 Replies

hi guys im a new 64 caddy owner and im having vaccumm leaks from the intake manifold. i took the manifold off today and it has cracks on it. my question here is, with the olsen gaskets with block off…Continue


Started by Michael Francioni in Wanted to Buy. Last reply by Michael Francioni on Friday. 2 Replies

Anyone have a turbo hydra matic transmission oil pump assembly?Continue

Blog Posts

Need help with a hood latch

Posted by Curtis Dover on January 2, 2023 at 5:23pm 0 Comments

Hey guys, I need some help.  Could someone send me some pictures on how the first hood release lever on a factory 1964 Cadillac is set up, where it comes though the grille. Not the secondary one. I need to know where the thumb or finger position is located through the grille. Is it above or below the center grille molding piece? Mine seems to be positioned behind the center molding piece and will not adjust above or below the molding. I have a wire tied to it to release it…


Oil pump

Posted by Ray Schick on October 30, 2022 at 4:34pm 4 Comments

I removed the front cover to change out the timing chain & gears all that went pretty well when I put the cover back on I put in a fresh oil filter ,filled it up figured it would be enough to prime the oil pump when I started the car .Fired up the car and heard lifters rattling, So I shut the car down right away. So I removed the oil filter housing, and poured oil down the neck of the oil pump housing filled it up and filled up the filter put it all together and fired it up and same…


Available parts

Posted by Thomas Reichenberger on October 13, 2022 at 11:47pm 0 Comments

Caddy members, I’m upgrading my 64 2-door coupe deville.

motor guy lost my block (machine shop went under) so I’m replacing motor & tranny with LS conversion. I have motor parts (other than block) for 429, rebuilt transmission, converter, and too many other motor parts not needed with fully dressed LS going in.

Email me ( or call me (210-739-4854) if you’re interested…..I live in San Antonio, TX.

thanks, TX…


Trunk Open and Lock Mechanism is in Closed Position

Posted by Chris Anderson on September 13, 2022 at 7:14pm 7 Comments

While working on my trunk lock on 64 Cadillac, I mistakenly closed the locking mechanism while the trunk was open.  Is there an easy way to manually release the lock back to the open position?



  • Add Videos
  • View All

© 2023   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service