You Know You Are Into Some Serious Car Doctor When You Have to Get the Ice Out!

You know you are into some serious car doctoring when you have to get the ice packs out. More to come on my 64 Coupe de Ville resuscitation in the next 1963/64 Cadillac Chapter Newsletter!  Mades some serious headway on honing in on the valvetrain noise issue ... and it was not quite what I expected. More to come in the next newsletter!

Views: 357

Reply to This

Replies to This Discussion

I believe ice packs are used in the treatment of cadmium poisoning. Is that the issue? LOL! But seriously, when is the newsletter coming out? Can't wait to hear what it is. Have you made a video or audio file of the noise?

Newsletter will hopefully be ready in 1 to 2 weeks.  I'll put the other 8 lifters in the engine tomorrow. You could hear the lifter tick pretty good in that leaving & returning out of the driveway video if you turn up the volume... it's actually embarrassing loud! LOL  I think I have found the problem ... and as noted a bit different from what I expected to find!  I do have some other isolated video and haven't posted here until I was ready to work on the car... else I would get a lot of speculations.  Within seconds of posting the driveway video I had one person post my intake might be cracked.
just fyi. I will be excited at the possibility of getting Dino running right again, but I'm not going to push anything. I enjoy the journey as much as the destination. I remember way back I threatened to rebuild my engine, and 5 years later I started the process and it took 3 months. I think Tony (hey Tony) was going to flip his lid at my slow pace! LOL 
Anyway, I have the 8 other lifters I couldn't install with valve covers off only, soakinng in some new oil as seen below and will install tomorrow and probably get the rocker arms and maybe valve covers back on. I have a new valley cover and that new Cad-Bling to install then I will go stare at my intake for  a day or two and decide if I want to go ahead and repaint.. or just stick on and try it out. The clean-up and repaint will be a slippery slope so I might want to just get everything back installed and cleaned up a bit as I go. I will at least have that fresh valley cover and bolts.  Here's the lifters adrift in Texas Tea:

 

New, Made in USA Melling Lifters and Push Rods. Prepping for install here... installed last night.  Valley cover went on this am.

I just read the story in the newsletter. So those lifters were installed by T-Hoff in the late 90's? If so has it been ticking for a long time? Really strange how that shorter lifter got in the mix. I would tend to believe that it is a different part number rather than a milling error but stranger things have happened I guess. Looks like a good tech tip is to compare all the lifters in size prior to installing.

No, I installed lifters when I rebuilt engine in 2012 and it run perfect with no noise until 2 years ago.

Just to add the head rebuild could be an article in itself. I dropped a valve just around the corner from the house, had the car towed to a touted "old car school professional" to have heads pulled and rebuilt. It sat there 2 weeks and I called them and they said, we can't get to the heads since the exhaust are still attached and we have not touched it. I'm like REALLY! So, I had it towed back home. I popped heads of with exhaust manifolds still attached, pulled exhaust off heads, and took to an old school engine builder named "Jason" at T-Hoff downtown Raleigh, NC. In a few days he had the head rebuilt with new parts and I had them back on the car. I am sure I probably replaced lifters then too, but the bad (i.e. short) lifter was put in by me when rebuild the engine in 2012. Other than the heads not much was put back in the engine that wasn't new.

Tony, You have what I am saying backwards. The lifter was significantly shorter than the others --> 7/100ths of an inch.  It is my belief that when the springs got a bit worn and couldn't compensate for the shorter lifter, resulting in excess valve lash, which caused some extra wear on the bottom ridge of the lifter as the cam lob  spunaround and met the lifter. Perhaps mushrooming is not the best word here. The  gap between lifter and lifter bore is between 5/10,000 and 2/1000th of an inch. On other words they are a very tight fit. It is my best guess the lifter was simply cast short. You can physically see the height difference and first thing I was drawn to:

 

Great to read that you got to the source of that annoying "tick" and that Dino is back on the road again.  And that engine compartment looks soooo good!  I never knew these cars had so much gold cadmium under the hood.

I got some interesting replies on the lifter issues. I think the point most people have missed is the fact that 7/100ths of an inch is a big visible difference.  Tolerances for these parts are in the 1000ths and 10,000ths, not 100ths. I had a couple suggess the lifter just wore down that much... that would be mind bending that in 3000 miles the lifter wore down perfectly flat retaining a like new surface appearance, and the other 15 lifters were completely unaffected. I think it has got to be a miscast but I'm keeping an open mind. I did not need a caliper when I looked a the lifter sitting below the rim of the lifter bore, and defintely didn't need one when I sat it next to a good 2" tall lifter as seen below.  This is one of the reasons I didn't want to try and explain it in a few sentences here and instead try to give details with pictures in the newsletter article.  The only thing I might add is that perhaps and maybe more plausible it is the incorrect lifter for my engine. More could be the same but height intended for another engine? Who knows... but for now we are good... knock on a metal valve lifter.... just don't squash it down short!
So.. here again is "shorty" next to a correct height new lifter...

Especially when  you are trying to "push your rod!"

RSS

Photos

  • Add Photos
  • View All

Forum

Modern radio antenna …

Started by Mack in 1963/64 Cadillac Specific Discussion on Tuesday. 0 Replies

Just replaced radios for the modern radios with Bluetooth and all the dance things and wanted to share how I went around the antenna knob… I’ve installed a regular two way GM window switch in the…Continue

BOOT

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Marty Smith on Tuesday. 1 Reply

I recently purchased a new boot for my 64 convertible and was wondering how difficult it s to install. I'm not very mechanical. It looks like the chrome piece behind and at top of seats needs to be…Continue

63 Exhaust Hanger Mystery

Started by Mike Travers in 1963/64 Cadillac Specific Discussion. Last reply by Cees de Bunje on Monday. 8 Replies

I'm in the process of installing a stainless steel single exhaust from Classic Exhaust on my '63 Coupe de Ville. I'm running into a mystery regarding my middle exhaust bracket. I have the bracket…Continue

TH400 Dipstick Tube Seal

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 9 Replies

In my “rebuild” of the transmission, I ordered a dipstick tube seal. However, I’m not sure if the right one came or how to best install the seal. I am wondering if anyone has replaced this seal OR…Continue

Blog Posts

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…

Continue

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service