Dan McNarry
  • Male
  • Calgary, Alberta
  • Canada
Share on Facebook
Share
  • Blog Posts
  • Discussions (141)
  • Events
  • Photos
  • Photo Albums
  • Videos

Dan McNarry's Friends

  • Brennan Brennan
  • Ron Westwood
  • John McNamara
  • Kim K Kaiser
  • Kevin Campbell
  • Will
  • Kurt
  • Tony and Ginny 429
  • Mark Geertsma
  • Jason Edge

Dan McNarry's Discussions

Replacement Rear Trailing Arms

Started this discussion. Last reply by Tony and Ginny 429 Nov 23. 7 Replies

Hello all,I haven't been on the forum for quite a while and do wish you all well. I would like to thank all of you who have purchased replacement rear trailing arms from me in the past. I realize…Continue

Oil Pan Gaskets

Started this discussion. Last reply by Kim K Kaiser May 26, 2020. 17 Replies

I don't know if any of you have attempted changing oil pan gaskets with the engine in the car but I have and it ain't easy. The biggest challenge is keeping the cork strips that seal the timing cover…Continue

Oil Pump Pressure Relief Spring

Started this discussion. Last reply by Dan McNarry May 7, 2020. 2 Replies

If anyone out there has a 63 or 64 shop manual, can you check something for me? What does the manual specify the length of the oil pump "regulator valve spring" to be? In the 62 manual the length is…Continue

Improving Cylinder Head Performance

Started this discussion. Last reply by Kevin Campbell May 2, 2020. 19 Replies

The stock Cadillac cylinder heads do a good job of getting the fuel air mixture into the engine and exhaust out at lower RPM's but are a little restrictive higher up the RPM range. Here is a little…Continue

 

Dan McNarry's Page

Latest Activity

Tony and Ginny 429 replied to Dan McNarry's discussion Replacement Rear Trailing Arms
"Norm  Go to part suppliers in the header for Dans contact info  His rear control arms are a great product and the only current solution to replacing the rear control arm bushings that will last  Enjoy "
Nov 23
Norm Waters replied to Dan McNarry's discussion Replacement Rear Trailing Arms
"Dan, I would like to order a set of your trailing arms for my 63 vert. How do I go about ordering a set? Thanks"
Nov 23
Kim K Kaiser replied to Dan McNarry's discussion Replacement Rear Trailing Arms
"I also hv a pair"
Jul 28
Tony and Ginny 429 replied to Dan McNarry's discussion Replacement Rear Trailing Arms
"Hi Dan Very nice to hear from you  Your control arms are helping many on this site and the only real solution to  the rear  control arm replacement so keep up your great work with reproducing  them  Your…"
Jul 28
Dan McNarry replied to Dan McNarry's discussion Replacement Rear Trailing Arms
"Hi Russ, Thanks for the input. I am looking at having the machine shop take over the complete manufacturing process from start to finish. It is getting to be a bit of a chore as I have had a few health issues lately and off loading the manufacturing…"
Jul 27
Russ Austin replied to Dan McNarry's discussion Replacement Rear Trailing Arms
"I have them on my own 63. Such an improvement. The pinion angle vibration is gone.  I can feel the difference in the ride quality. It took some of the boat sway away and gave an improved ride.  I also have the inserts that go into the…"
Jul 26
Jan Johansson replied to Dan McNarry's discussion Replacement Rear Trailing Arms
"Hello Dan I hope you continue providing trailing arms. I plan to order a pair later this year Jan"
Jul 26
Dan McNarry posted a discussion

Replacement Rear Trailing Arms

Hello all,I haven't been on the forum for quite a while and do wish you all well. I would like to thank all of you who have purchased replacement rear trailing arms from me in the past. I realize that there are still customers out there for this product but I am at a bit of a cross roads. I would like to continue but over the last 4 years the cost for machining and waterjet services as well as steel have gone up and my price hasn't changed.I would like to increase my price to $420 from $385 but…See More
Jul 26
Dan McNarry and Brennan Brennan are now friends
Jul 2
Anders liked Dan McNarry's discussion Polyurethane Replacement Trailing Arm Bushings
Apr 25
Dan McNarry replied to Ian Osborne's discussion Exhaust Manifold Gaskets......Again
"I've had custom exhaust gaskets made for radial aircraft engines in both grafoil and copper. If there is an interest I could see about having sets made and was thinking copper as Ian has done but grafoil for the manifold to pipe gasket. If…"
May 31, 2020
Dan McNarry replied to Dan McNarry's discussion Caddy Daddy
"Tony, the new to me peace of mind regarding my fuel was put to the test today. We took a nice drive in the mountains and went a longer route than we normally would knowing we would easily make it back on the tank full we started out with. No…"
May 30, 2020
Dan McNarry replied to Ian Osborne's discussion Exhaust Manifold Gaskets......Again
"Nice job fabricating your gaskets. Here is a pretty good option that I use. They are grafoil gaskets from Remflex. I use them on my car with my home built headers and they work great. I would expect that they would work equally well on stock…"
May 30, 2020
Tony and Ginny 429 replied to Dan McNarry's discussion Caddy Daddy
"Dan  Glad to here your fuel gauge is now working as it should  with parts fro Russ ñand good peace of mind from that on the road  I think you must have your trans out while doing your clutch work and oil pan work If so do…"
May 30, 2020
Dan McNarry replied to Dan McNarry's discussion Caddy Daddy
"Russ, I installed the sending unit yesterday afternoon and went and filled the car up this morning. The gauge now reads accurately and I'm really happy to have it working again, makes road trips a lot less stressful. Thanks for a great product."
May 30, 2020
Kim K Kaiser replied to Dan McNarry's discussion Oil Pan Gaskets
"prudhomme was the "snake""
May 26, 2020

Profile Information

Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
No, I own a 1962
Cadillac LaSalle Club Member? If Yes, Membership #?
No
1963/64 Cadillac Chapter Member?
No

Comment Wall (4 comments)

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

At 12:50pm on April 5, 2020, Will said…

Hi Dan

V4L 1M7

thanks

will

At 12:59am on April 2, 2020, John McNamara said…

Thanks Dan

Colour is not important to me.

Shipping adddress will be:

John McNamara

Strata Worldwide

1/8 Channel Road

Mayfield West NSW Australia 2304

 John

At 10:01pm on March 31, 2020, John McNamara said…

Dan

I am also interested in a set of your rear bushings.

Thanks John McNamara

Australia

At 7:13pm on January 21, 2018, Jason Edge said…

Welcome to the 63/64 Cadillac Website. 

This site is hosted by the CLC (Cadillac LaSalle Club) 1963/64 Cadillac Chapter. Joining the website is free to everyone, however, you must be a CLC member to join the chapter. 

- Click Here for more information on joining the 1963/64 Cadillac Chapter and the Cadillac LaSalle Club

Be sure and check out all the links and pages and make yourself at home.  The Help Page at www.help.6364cadillac.com will have links to many useful articles and information about our Cadillacs.

 
 
 

Photos

  • Add Photos
  • View All

Forum

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 5 hours ago. 287 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Door edge guards for 63 convertible

Started by Louie Hernandez in Wanted to Buy. Last reply by Rudolph Kutey 5 hours ago. 1 Reply

Looking for a good set for a 2dr Eldo. Thanks!Louie -   louzer21@gmail.comContinue

Crankshaft for sale.

Started by Russ Austin in General Discussion yesterday. 0 Replies

A cleaned and polished crankshaft for a 64 429 with the Hydra Matic transmission.A machine shop did the work and is guaranteed.Crank is 300.00  plus shipping.   email me at  russ@thecadishack.com Continue

64 429 engine block for sale

Started by Russ Austin in General Discussion yesterday. 0 Replies

I have a machined 64 429 engine block for sale.  A machine shop cleaned, bored and inspected the block.  Cylinders are bored to 30 over stock. Guaranteed good.  500.00  plus shipping. email me at …Continue

Blog Posts

1963 & 1965 Distributor

Posted by Martin McKercher on November 9, 2021 at 8:34pm 5 Comments

Hi all
I am looking to have an aftermarket distributor made for these year models.
I have fitted a Holley Sniper to my 63' 390 & want the Sniper to control the timing.

This is in the very early stages so I am looking to see if it is viable.
I understand the purists might see this as sacrilgious but the Sniper has made my car soo much better for me.
I am asking to see if there is any interest?

1964 Eldorado for Sale

Posted by Richard Stanley on October 29, 2021 at 1:41pm 0 Comments

After 26 years as second owner, I have decided to sell my 1964 Eldorado.  Feel free to call me anytime to discuss.

https://www.facebook.com/marketplace/item/1764798240358992/

Best,

Richard Stanley

213 300-4567

What is the color of this 63 Eldorado - aquamarine or green?

Posted by SK on October 24, 2021 at 2:33pm 2 Comments

Hi, 

I really like the color combination of this 63 Eldorado (sold long time ago by Volocars).

The ad states aqua exterior and green interior but unfortunately there is no pic on the cowl tag.   

Is the exterior color ’Frost aquamarine’ and interior ’Beryl’?

Or is the exterior green, ’Frost green’ and interior ’Emerald’?

-Samu…

Continue

Rochester throttle body gasket

Posted by Phil on September 29, 2021 at 8:18am 5 Comments

Hello,  would anybody be able to tell me if I’m using the correct gasket on my Rochester throttle body? It doesn’t  look right to me.  I’m not sure if the carb actually ran with this gasket because I got it used with no history.  Any help would be appreciated …

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service