Greg Kostefko
  • Male
  • Winnipeg, MB
  • Canada
Share on Facebook
Share

Greg Kostefko's Friends

  • paul k
  • Mike Foose
  • Russ Austin
  • Jason Edge

Greg Kostefko's Discussions

'64 Sedan DeVille for sale.

Started May 31, 2018 0 Replies

Hi all,Firstly I don't own this car nor do I have any affiliation with the seller so any questions should be posed to the owner.I spotted an ad for a '64 SdV being sold in Southern Ontario.…Continue

Caddy Shack Restorations - A Review

Started this discussion. Last reply by Joan Ramon Prats Apr 19, 2017. 11 Replies

Hi All,I just wanted to take a second to give a quick review of dealing with Russ @ Caddy Shack. Firstly a little background. I purchased a '63 Coupe last fall and went through it to see what parts I…Continue

Antenna Motor Rebuild

Started this discussion. Last reply by Clovis Nov 16, 2016. 6 Replies

Good Morning All,I've pushed the '63 to the side of the garage for the winter. Snow is on it's way so the garage has to go back to being a garage again. As she is in the midst of a restoration I have…Continue

Door / Trunk / Ignition Key Question

Started this discussion. Last reply by Tony and Ginny 429 Sep 4, 2016. 11 Replies

HI all,I have finally started the project of restoring my '63 Coupe. Problem is I inherited a few headaches and little actual info. The previous owner(s) have left the car in various states of…Continue

 

Greg Kostefko's Page

Greg Kostefko's Photos

  • Add Photos
  • View All

Greg Kostefko's Blog

WANTED: 390 cid for a 1963 Coupe DeVille

Posted on August 21, 2013 at 10:53am 3 Comments

Hello all,

I was just wondering if anyone had, or knew of, a 390cid engine for a '63 Coupe Deville that was for sale. It basically needs to be a complete engine from the air cleaner down as the project I'm contemplating has nothing under the hood. A/C optioned engines are preferred. Would prefer one that was running when pulled but as I was a mechanic by trade it's not a deal breaker if it didn't run.

I know it's asking a lot from a new member but I know someone here can…

Continue

Introduction

Posted on August 21, 2013 at 9:49am 0 Comments

Hi all,

Finally had a few minutes to sit in front of the computer and make a post. I guess I should start with a bit about myself. I'm 37 and live in wonderful Winnipeg, MB Canada. If you look at a map of North America I'm pretty smack dab on the middle of it all!

I'm currently negotiating with a fellow to try and obtain a 1963 Coupe DeVille he has sitting on his property. He started working on it but gave up as he has far too many projects on the go. If the dollars and cents…

Continue

Comment Wall

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

  • No comments yet!
 
 
 

Photos

  • Add Photos
  • View All

Forum

Chapter Member? Got a 63 or 64 Cadillac for Sale? Let's Run it in the Newsletter!

Started by Jason Edge in For Sale. Last reply by Jason Edge 3 hours ago. 4 Replies

One of the new features of recent newsletters is a Member Classified Cars for Sale section.…Continue

vacuum canister

Started by Walt Timmerman in General Discussion. Last reply by Rob Shatsnider 8 hours ago. 15 Replies

what is the vacuum canister for that is behind the drivers front fender?After removing my fender I see its got a hole in the top but nothing is hooked to it and no line is laying there.Any help would…Continue

New Batch of Embroidered Iron-On 1963/64 Cadillac Chapter Patches - $4 each

Started by Jason Edge in Chapter Discussion. Last reply by mark zimmerman 13 hours ago. 10 Replies

As noted in our August 1963/64 Cadillac Chapter Newsletter:Around 6 years…Continue

Tags: Available, Patches, Chapter, Cadillac, 1963/64

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Daniel Grande 21 hours ago. 9 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

Blog Posts

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service