antonio bravo
  • Male
  • Corona, CA
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (1)
  • Events
  • Photos
  • Photo Albums
  • Videos
 

antonio bravo's Page

Profile Information

Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
1963 coupe series 62
Cadillac LaSalle Club Member? If Yes, Membership #?
No
1963/64 Cadillac Chapter Member?
No

Comment Wall (2 comments)

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

At 5:40pm on October 22, 2017, antonio bravo said…
Hello, I have a 1963 coupe DeVille with a 390 and I’m dropping in a 429 from a 1967 DeVille. I will cut and weld the oil pan to change locations of the sump, and probably extend the tube on the oil pick up. do you know if there is an oil pan and oil pick up tube I can use to eliminate my fabrication work?
At 10:36am on October 16, 2017, Jason Edge said…

Welcome to the 63/64 Cadillac Website. 

This site is hosted by the CLC (Cadillac LaSalle Club) 1963/64 Cadillac Chapter. Joining the website is free to everyone, however, you must be a CLC member to join the chapter. 

- Click Here for more information on joining the 1963/64 Cadillac Chapter and the Cadillac LaSalle Club

Be sure and check out all the links and pages and make yourself at home.  The Help Page at www.help.6364cadillac.com will have links to many useful articles and information about our Cadillacs.

 
 
 

Photos

  • Add Photos
  • View All

Forum

Surprised no feed back on the 65 429 rear crank bearing redesign change Service

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion. Last reply by Kurt 11 hours ago. 12 Replies

As the  rear crank bearing was redesigned in the 65  429 by Cadillac to reduce pressure on the RMS I thought it might be the answer to our endless leak issue many are having No one has found a…Continue

Love my car but hate the brakes - need some good advice

Started by Walter Anderson Bonner Jr. in General Discussion. Last reply by Mack on Thursday. 9 Replies

Need some advice: My car swerves when stopping.  The mechanic noticed the problem when he drove the car and he adjusted all of the vehicle’s drum brakes.   He, noted the brakes and drums looked good…Continue

Mark S Anderson

Started by Tony and Ginny 429 in 1963/64 Cadillac Specific Discussion on Thursday. 0 Replies

Sent you a friend request Continue

Front Dash Speaker

Started by Michael Vogler in General Discussion. Last reply by Tony and Ginny 429 on Wednesday. 15 Replies

I want to replace the front dash speaker in my ‘64 De Ville Conv.  Do I really have to take the dash pad off, to access it from the top (As I read in the shop manual)? Or does anyone have tip to…Continue

Blog Posts

Rochester throttle body gasket

Posted by Phil on September 29, 2021 at 8:18am 5 Comments

Hello,  would anybody be able to tell me if I’m using the correct gasket on my Rochester throttle body? It doesn’t  look right to me.  I’m not sure if the carb actually ran with this gasket because I got it used with no history.  Any help would be appreciated …

Continue

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service