Norman Silverman's Blog – December 2018 Archive (4)

Brighter Headlights. What to install that won't draw too much current.

My car still has its "T-3"headlamps and they shed poor, yellow-tinted light. I'd like to replace them with something that most folks on this web site use, that would shed good light and don't heat up the wiring with too many amps. 

Survey says?

Norm

Added by Norman Silverman on December 15, 2018 at 9:07pm — 30 Comments

Although the radiator was not leaking, nor was the car running hot, I tool out the radiator today to have it boiled out and rodded out. Then I changed the oil and filter (filter is very easy to reach…

Although the radiator was not leaking, nor was the car running hot, I tool out the radiator today to have it boiled out and rodded out. Then I changed the oil and filter (filter is very easy to reach with the radiator out), then the thermostat got changed. 

I'll have the radiator back from the shop on Monday, and will reinstall it then. 

Still having…

Continue

Added by Norman Silverman on December 8, 2018 at 9:29pm — 15 Comments

Trunk Light Socket Very Strange?

I went to replace the bulb in the trunk light socket and was met by something I had never seen before: the socket appears to be made in two thicknesses. First a wide one with appropriate cut outs on the side where the bulb nipples fit in, then a long slender shaft (with a cardboard tubular insert) down to the positive contact. I've never seen anything like this. Only thing I can figure is that it is designed to have a metal rod inside the cardboard shaft that…

Continue

Added by Norman Silverman on December 4, 2018 at 10:14pm — 2 Comments

Comfortron Power Module Reinstalled; BLOWER BLOCKAGE FOUND!!

I got the rebuilt Power module back from the rebuilder and reinstalled it.

It's been a while since i posted on this topic so I will remind those reading that the main problem I have been chasing is that i can't get air out of the AC or the heater ducts-even though the heat/ac vacuum solenoid is working. Today, I found out why.

I installed the newly rebuilt Module but it…

Continue

Added by Norman Silverman on December 4, 2018 at 12:51am — 5 Comments

Photos

  • Add Photos
  • View All

Forum

Very sensitive brakes.

Started by Phil in 1963/64 Cadillac Specific Discussion. Last reply by Phil 9 hours ago. 18 Replies

Hey everyone,  how sensitive should the power brakes be?  I have just rebuilt the power booster and  replaced the master cylinder. The pedal doesn’t have any resistance so I have to be very gentle so…Continue

New Batch of Embroidered Iron-On 1963/64 Cadillac Chapter Patches - $4 each

Started by Jason Edge in Chapter Discussion. Last reply by Jason Edge 9 hours ago. 8 Replies

As noted in our August 1963/64 Cadillac Chapter Newsletter:Around 6 years…Continue

Tags: Available, Patches, Chapter, Cadillac, 1963/64

63 rear main seal

Started by Luther in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 16 hours ago. 9 Replies

Hello all , just spent better part of the weekend installing a new rear main seal and pan set on my 63 390 , all though it slowed the leak down considerably , l still have a drip , l used a Felpro…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 20 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service