Jason, Would you like the dimensions?

I read a comment you made about the splash guard for the battery. Would you like the dimensions?

Views: 718

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Jason Edge on August 16, 2014 at 8:18pm

Note, Once I get the dimensions I have a sheet of masticated rubber and can create a template and cut as many as I want.  For anyone with a1964 missing this piece (probably most of you), I'll sell for $10 + s/h (probably $6 priority in USA).  Jimmy, you get one on the house if you come up with the specs. 

Comment by Jason Edge on August 16, 2014 at 8:15pm

Yes I am curious of dimensions. I also need to know how far from left edge and top edge the top left bolt hole center is located to be able to cut for approximate placement.

The upper left attaching bolt is a 3/8" hex head bolt with washer bolted to small right able bracket held in place via 5/16" hex head metal screws from the bottom of the upper grill assembly top painted triangular section. It is approx. 8.5" from right edge of the upper triangular piece as seen in picture below:

Comment by Jimmy Davis on August 16, 2014 at 7:38pm

One hole in the rubber was mounted on the bolt in the highlighted circle. I cannot find where the other was mounted on the part car the rubber came from, or, my driver car.

Comment by Ray Schick on August 16, 2014 at 6:39pm

Hey Jimmy , where exactly is that shield mounted ? I see the bolt holes in it. That is a factory item?

Photos

  • Add Photos
  • View All

Forum

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 25 minutes ago. 275 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Dash Grille - Adhesive?

Started by Chris McBride in General Discussion. Last reply by Chris Codd 1 hour ago. 2 Replies

This dash grille likes to vacation from the dashboard.  Is it properly secured with an adhesive and, if so, what adhesive?  If so, what type?  If not, how is it secured?Thank you.…Continue

Wiper Blades for a '63?

Started by Karl Schwarz in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 18 hours ago. 3 Replies

Is there anything special about the wiper blades I should use on my '63 Series 62 convertible? I have the original arms with the original blade brackets. I got Anco N-18R blades that should fit. I…Continue

Resistance wire removal or replacement

Started by Anders in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 20 hours ago. 38 Replies

Resistance wire removal or replacement.If installing an electronic ignition system the resistance wire most likely has to be removed or bypassed. There are several ways to do this and the solution…Continue

Tags: wire, resistance

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Events

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service