Hello All,
I have one of the original keys to my 63 and it has the code of 9477. Is there anyway to find out the code of the other key. It would be great to get a set of keys cut to code just like when she came off the showroom floor.

Thanks in Advance,

Views: 290

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Bill Smith on August 30, 2013 at 7:14am

The original envelope is postmarked May 1991.Return address is Cadillac Motor Division ,Detroit, Michigan and handwritten next to return address is 'Greg Wallace, dept. 809' He used to run an ad in Hemmings and if I remember correctly was a member of CLC. Jason, I am curious to know if you have ever found a build sheet in any of the 40 or so cars you have parted? I have parted around a dozen 63-64's and have never found one. Have found them in Pontiacs I have parted, sometimes 2 in a car. Usually stuffed in the back seat springs.

Comment by Jason Edge on August 30, 2013 at 6:13am

Sadly, the newer build sheets blanks out the other cars built that are listed on that page. I have both an early and later provided build sheet.  I like seeing all the other cars. Bill, when did your order your build sheet?

Comment by Ron Collins on August 30, 2013 at 12:43am
I was looking at the site last night, I will for sure be ordering my build sheet tomorrow morning.

Thanks Again Bill,
Comment by Bill Smith on August 30, 2013 at 12:15am

Attached is a copy of my build sheet with key numbers.

Comment by Ron Collins on August 29, 2013 at 1:09am
Pulled out the lock and of course there was no code on it. But the good thing is I have one code. Will take the cylinder to a locksmith and have them cut a perfect key for me. Hope it's too expensive. Think I will spring for a build sheet as well.
Comment by Ron Collins on August 27, 2013 at 8:25pm
Thanks Jason,
Always a great source of info.
Comment by Ron Collins on August 27, 2013 at 8:24pm
Thanks Bill,
That will definitely help!!!
Comment by Jason Edge on August 27, 2013 at 7:36pm

The key codes on my build sheet were blank. I think a locksmith can get the code off the cylinder and cut new keys using original stock keys.  I would be curious how many others have or don't have the key codes on their build sheets?  I had forgotten there was even a column for it since mine just had blanks.

Comment by Bill Smith on August 27, 2013 at 5:16pm

Ron, Here is a link to order a build sheet for your car from the GM Heritage site. I bought one for my car when the archive was in the hands of Greg Wallace about 20 years ago. It had the key codes on the build sheet. Good luck, Bill    http://www.gmmediaarchive.com/?page=2

Photos

  • Add Photos
  • View All

Forum

The Australian Bushfires:.......

Started by Kevin Campbell in General Discussion. Last reply by Kurt 23 hours ago. 10 Replies

I know we have some Aussies on here and I have to say, Australia, is in a whole world of hurt at the moment, so do ya best to stay safe.Currently, in the southern states, 4 huge fire fronts, look…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

How much play in 63 timing chain?

Started by Ben Roberts in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 yesterday. 4 Replies

I will be installing a new chain and gears because I'm in this deep and all the forums here strongly recommend doing so.  It appears the coating is intact and I don't have to worry about that debris…Continue

Harmonic balancer holes are too shallow for the 3 bolts of puller

Started by Ben Roberts in 1963/64 Cadillac Specific Discussion. Last reply by Ben Roberts on Friday. 3 Replies

Trying to pull 1963 390 harmonic balancer.  The holes needed for the 3 bolts on the puller can only thread in 1/4” which is not enough to run an impact wrench on it.  I ran a tap to clean the threads…Continue

Blog Posts

1964 429 Aluminum Front Cover For Sale!

Posted by Jeff Kinzler on January 12, 2020 at 3:30pm 1 Comment

  • I wound up with an extra front cover for my '64 and offering it for sale.

Purchased from a knowledgable part supplier with thorough hands-on knowledge of 63-64 Cadillac engines, who checked the part before sending it to me. The oil pump driven gearSee S bore and the pressure relief piston bore are both .002 over and within the .005…

Continue

Looking for the Rochester Choke Tube ...

Posted by Mack on January 10, 2020 at 1:14am 3 Comments

37E244B6-71C7-4857-8D50-1BD8C48077A4.jpeg

Looking to buy the choke tube for my Rochester... anybody have one for Sale???

AC/heater for 1964 Cadillac coupe de ville

Posted by Matias J. Adrogue on January 7, 2020 at 11:11am 9 Comments

Good morning!  I am Matias Adrogue.  I bought a 1964 Cadillac coupe de ville last year and am real close to the final restoration details!  I call her “Jaws 64”.  Pics will be posted soon.  I need advise regarding a AC/heater.  It came stock in the vehicle but it does not work.  A mechanic gave me a bid of $1700 to replace and repair.  I am ready to install a new system - Vintage Air or Old Air Products from Fort Worth Texas.  I would greatly appreciate your thoughts.  I read the great write…

Continue

63 cadi conv

Posted by Merlino jean marc on December 31, 2019 at 2:51pm 0 Comments

Hello everyone 

As a European, I fell in love with Americans cars and Americana stuff.

I bought a running 63 for cheap .but there is no secret when you buy cheap ,it is big project. The car needs everything. Overtime I was able to slowing buy parts .actually  I am looking for the passenger front lower section which is becoming harder ,and harder to find

The car has a lot of issue with rust.it needs a paint,a top and I need to replace all floor pans.with patience and…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service