seat belt retractor spring for sale

Just picked up a seat belt retractor spring. This is what retracts the seat belt into the retainer, on a 64.

If your seat belt is no longer retracting automatically, your spring is broken. These are not being reproduced, so get this as a spare.

25.00 plus shipping.

My email;  russ85747@hotmail.com

Views: 149

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Russ Austin on January 18, 2016 at 11:25am

The new springs are in.   They showed up while I was in Midland Texas.   These are new reproduction of the original spring, and will retract the front seat belt superbly.

20.00 each,  or a pair for 35.00     These will ship for 6.50 anywhere in the states.

email me for international rates, or to order yours today.    russ85747@hotmail.com

 I did a craigslist search for 63 or 64 Cadillac's in Midland TX, and didn't even find anything in the surrounding area's.  Them Texas fella's sure like their trucks.

Photos

  • Add Photos
  • View All

Forum

Replacing Front Door Window Chrome Channel

Started by Michael Vogler in General Discussion 1 hour ago. 0 Replies

List Mates,My '64 De Ville Conv. front door window chrome trim needs to be replaced.  The chrome on both front door window his getting a little bit of pealing off.  I have the chrome replacement…Continue

Vacuum advance

Started by Thomas Yarri in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 15 hours ago. 1 Reply

Good afternoon to all my fellow Cadillac owners! I have a question about the vacuum advance on my car. The car is a 64 without a/c and a Rochester carburetor. I noticed that I have vacuum at the port…Continue

1963-1964 Convertible Parts

Started by Charles Fares in For Sale 21 hours ago. 0 Replies

1963-64 Convertible top switch with chrome bezel and mounting retainer clip, tested and working, nice chrome, $65. 1963-64 Convertible rubber A-pillar seals LH and RH pair (repops) $50 the pair.…Continue

Over heating

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 22 hours ago. 9 Replies

Hi, been doing the break in still. At about 450 miles.I hve noticed that when i go out, temp gets to between 1/4 and 1/2 on the gauge.  If i sit any period of time or dnt keep moving, it creeps…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service