I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.

Views: 50

Comment

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

Comment by Gene McIlroy on August 12, 2019 at 11:51pm

Jason, I appreciate you correcting the post.  Not a problem at all I tried but just could not figure it out.  Thanks

Comment by Jason Edge on August 12, 2019 at 8:32pm

Gene, I usually don't mess with anyone's post but took the liberty to correct your post by swapping out the correct picture. When you post from a desktop/PC you just click Edit up top to make changes. If on a mobile device you will need to make sure you are in "desktop view" to make the edits. There is a drop down menu when on mobile devices where you can select desktop view. This might not be your issue but feel it is always worth repeating for the ever growing number of mobile device users. I tend to "look" at stuff on my iPhone but post and edit stuff on the desktop .. but that's just me.

Comment by Jason Edge on August 12, 2019 at 8:28pm

Gene, Thanks for the alternate source. This one piece of rubber that holds up pretty well as seen by your original sample but always good to find new rubber replacements.

Photos

  • Add Photos
  • View All

Forum

Rear glass

Started by David Stapp in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 9 hours ago. 9 Replies

anyone know of a company that makes the rear glass for our cars? I can’t seem to find any. 1964 4 door 4 window hard top.…Continue

front engine pulley removal

Started by tom servas in 1963/64 Cadillac Specific Discussion. Last reply by tom servas 10 hours ago. 7 Replies

Am removing the front cover on our 64 engine with AC. Have all 6 bolts that hold the pulley onto the damper removed, can wiggle the pulley BUT it will not come fully off the damper, Is there…Continue

Where can I buy resistance wire for my 1963?

Started by Tim Walterson in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin 15 hours ago. 3 Replies

Hello - just signed up for this forum - looks like a great resource!  I perused the posts and did some searches.  I see most of the posts related to my questions are about doing away with resistance…Continue

Blog Posts

Is there a separate Starter Relay, or does the Solenoid serve that purpose?

Posted by Norman Silverman on August 30, 2019 at 5:57pm 7 Comments

Hello All.

I will be replacing the starter solenoid tomorrow (actually my mechanic will do the work, I'll just supervise). In checking the FSM electrical schematic and chapter verbiage, I don't see anything that looks like (or is referred to as) a starter Relay. It seems the Starter Solenoid serves the function and there's no separate relay. Right or Wrong?

If wrong, where…

Continue

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 8 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …

Continue

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service