Denny Link
  • Male
  • Hamersville, OH
  • United States
Share on Facebook
Share

Denny Link's Discussions

Washer

Started this discussion. Last reply by Jason Edge Jan 26, 2017. 2 Replies

I have a 1964 with a 429.  Does a washer and bolt go into the end of the crankshaft?   If so, what size washer would go on there?Any help would be appreciated.DennyContinue

Problems

Started this discussion. Last reply by Tony and Ginny 429 Dec 10, 2016. 4 Replies

2 questions.I dropped a socket in the distributor shaft. Can't seem to fish it out. Will it cause problems?Can anyone give advice on priming the oilPump.Any advice on these issues would be…Continue

Problems

Started Dec 9, 2016 0 Replies

2 questions.I dropped a socket in the distributor shaft. Can't seem to fish it out. Will it cause problems?Can anyone give advice on priming the oilPump.Any advice on these issues would be…Continue

priming oil pump

Started this discussion. Last reply by Russ Austin Dec 2, 2016. 1 Reply

Question,  what size socket do I need to prime a 64 caddy Deville oil pump?ThanksDennyContinue

 

Denny Link's Page

Profile Information

Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
1964 sedan deville
Cadillac LaSalle Club Member? If Yes, Membership #?
28646
1963/64 Cadillac Chapter Member?
28646

Denny Link's Photos

  • Add Photos
  • View All

Denny Link's Blog

bearings

Posted on January 7, 2015 at 11:30pm 1 Comment

can anyone tell if anyone in the usa makes wheel bearing.....thanks....looking forward to make it to Wis

.

bearings

Posted on January 7, 2015 at 11:30pm 0 Comments

can anyone tell if anyone in the usa makes wheel bearing.....thanks....looking forward to make it to Wis

.

Parts for Sale 63/64 Caddy

Posted on July 8, 2014 at 9:23pm 0 Comments

1 used carb heat insulator in good condition

1 429 manifold

1 64 dash in fair condition

4 radios

Set of Windows for 64  4 door glass all very good frames fair

3 sets of hub caps in fair condition

Please contact me at everydaydenny@roadrunner.com or call me at 513-310-8714,   I will have the parts with me at the car show on Saturday July 12 at the Grand National…

Continue

Comment Wall (3 comments)

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

At 2:49pm on May 21, 2015, Jason Edge said…

Denny,

On the 1964 eyebrow molding under the headlights:
I have 2 lefts: one poor one VG with nice chrome. The price is $30. 
I have 5 lefts: all poor to fair with corrosion or dings. I have one in fair with just a minor ding/bad area in one spot. It would be good to replace a poor condition one or to have as a rechrome core. The price is $10. If interested email me at jasonedge@nc.rr.com with address and will get you a total with shipping and payment details. thanks, Jason.  

At 10:46am on October 12, 2014, Russ Austin said…

Denny, staert a new thread with your problem. Will be glad to help out. Need to know what the symptoms are.

At 4:55pm on March 9, 2014, Jason Edge said…

Welcome to the 63/64 Cadillac Website.  

Be sure and check out all the links and pages and make yourself at home.  

I am glad to see that you are a member of the Cadillac LaSalle Club however I do not have you on our chapter roster. If you would like to join please email me at jasonedge@nc.rr.com and provide name, address, email, and any 1963 and 1964 Cadillacs by body style that you own.

Jason Edge
Director 1963/1964 Cadillac Chapter

 
 
 

Photos

  • Add Photos
  • View All

Forum

Whoa there, you want how much??

Started by Robert Gonzalez in 1963/64 Cadillac Specific Discussion 17 hours ago. 0 Replies

Ok, I’ve been on here for almost a decade. I KNOW we covet our cars and have always tried selling them at premium prices. But the bottom line, our cars rarely fetched prices over a covair. The…Continue

1964 Cadillac parts for sale... northern cali

Started by Jason in For Sale. Last reply by Jeremy yesterday. 1 Reply

Bill Hirsch cast iron gray exhaust and manifold paint (1 can) $20Bill hirsch Cadillac dark blue engine enamel high temp high gloss (2 cans) $40Convertible top latchValve coversHeadlight bezelRadioGas…Continue

Tags: Parts

63 4 door Cadillac

Started by Walt Timmerman in For Sale. Last reply by Jeremy yesterday. 7 Replies

Need to start parting this car out. Might be moving soon and if its not parted out, it'll be scrapped.Also have Motor and transmission from my 63 coupe deville for sale. will part out also.Was told…Continue

Free- 64 lower bumper bucket - Passenger side

Started by Michael Buonaccorso in For Sale. Last reply by Jeremy yesterday. 1 Reply

This is in rough shape. Not only is there rust in the usual places but it is also bent. I replaced this piece on my car after an accident, but since this is a hard to come by piece, I figured someone…Continue

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service