Kraig Wire
  • Male
  • Morgantown, WV
  • United States
Share on Facebook
Share

Kraig Wire's Friends

  • Jason Edge

Kraig Wire's Discussions

1963 390 engine and trans for sale

Started this discussion. Last reply by paul Jul 19, 2020. 1 Reply

I have a rebuilt 390 that runs well with very low miles. New Edelbrock 1406 carb and new Edelbrock air filter.New intake gaskets, plugs and wires.New fuel filter and fuel lines,and fuel pump.Also…Continue

1963 Sedan Deville Park Avenue engine and trans for sale

Started this discussion. Last reply by paul Jul 19, 2020. 4 Replies

Doing LS swap, selling rebuilt 390 with low miles and a rebuilt Hydromatic not sure what they’re worth but make offer. I have recent pics and videos of car running and driving. Thanks

Power steering pump shaft bushing part #?

Started this discussion. Last reply by Tony and Ginny 429 Apr 2, 2019. 4 Replies

Hello everyone,I’m rebuilding the power steering pump on my 63 Park Ave and ran into a problem. The shaft bushing that came in the rebuild kit is slightly larger in diameter than the original. It is…Continue

Need help finding a new dipstick tube seal for Hyromatic

Started this discussion. Last reply by Kraig Wire Feb 6, 2019. 3 Replies

Hello everyone,I have a 63 Sdv Park Ave with the Hydromatic trans and need a new dipstick tube seal. I would appreciate any advice as to where to purchase one. Thanks!Continue

 

Kraig Wire's Page

Latest Activity

paul replied to Kraig Wire's discussion 1963 390 engine and trans for sale
"I'm interested if you still have this Paul."
Jul 19, 2020
paul replied to Kraig Wire's discussion 1963 Sedan Deville Park Avenue engine and trans for sale
"Hello do you still have this. I would be interested for sure I'm in central fl Paul"
Jul 19, 2020
Bob Willis liked Kraig Wire's photo
Dec 30, 2019
Kraig Wire replied to STEPHEN HORWATH's discussion TURBO HYDRAMATIC
"If you click on his name it shows where he’s from Pa."
Sep 14, 2019
Kraig Wire left a comment for Andy Bourque
"Did you want to talk about that engine and trans for sale ?"
Sep 14, 2019
Kraig Wire posted a discussion

1963 390 engine and trans for sale

I have a rebuilt 390 that runs well with very low miles. New Edelbrock 1406 carb and new Edelbrock air filter.New intake gaskets, plugs and wires.New fuel filter and fuel lines,and fuel pump.Also have a rebuilt Hydromatic Trans with new pan gasket and dip stick tube o ring recently replaced. Will sell separate but prefer to sell as package so I can show the buyer what they’re getting a good running and shifting power train. Engine and trans is still in a 1963 Cadillac Sedan Deville Park Avenue.…See More
Sep 14, 2019
Kraig Wire replied to Kraig Wire's discussion 1963 Sedan Deville Park Avenue engine and trans for sale
"6.5 hrs away from you"
Sep 12, 2019
Kraig Wire replied to Kraig Wire's discussion 1963 Sedan Deville Park Avenue engine and trans for sale
"I’m in Morgantown,Wv but the Car is from CA"
Sep 12, 2019
Andy Bourque replied to Kraig Wire's discussion 1963 Sedan Deville Park Avenue engine and trans for sale
"Where are you located?"
Sep 12, 2019
Kraig Wire posted a photo
Sep 7, 2019
Kraig Wire posted a discussion

1963 Sedan Deville Park Avenue engine and trans for sale

Doing LS swap, selling rebuilt 390 with low miles and a rebuilt Hydromatic not sure what they’re worth but make offer. I have recent pics and videos of car running and driving. Thanks
Sep 7, 2019
Kraig Wire commented on Steven Platt's blog post 1963 Cadillac 390 engine and transmission for sale
"I’m doing the same thing with my 1963 Park Avenue. I also have a good running 390 and good shifting Trans up for sale. Make offer I have pics and videos if interested"
Sep 7, 2019

Profile Information

Do you own any 1963 & 1964 Cadillacs? If Yes, Year & Body Style
1963 Sedan Devil
Cadillac LaSalle Club Member? If Yes, Membership #?
No
1963/64 Cadillac Chapter Member?
No

Kraig Wire's Photos

  • Add Photos
  • View All

Comment Wall (3 comments)

You need to be a member of 63/64 Cadillac Website to add comments!

Join 63/64 Cadillac Website

At 1:08pm on January 20, 2019, Tony and Ginny 429 said…
Kraig

I am running an Edelbrock 1406 on my 64 429 with the stock mechanical fuel pump with no problem regarding fuel pressure
If using the stock backerlight blk spacer you need to block off one of the two PVC inlets to the carb as you now have two ( one on top of the other )
You will now have two places to connect your vacuum advance
The best one to use is the one on the drivers side of the carb closing off the other
That will improve your timing advance curve over the stock set up to give you more power thru the RPM range which is another benefit of using the Edelbrock carbs over a stock rebuilt carb ( the performance people )

I assume you removed the intake and blocked off the correct heat passages for the old chock so you can now use the new electric choke

I did have to rejet my carb on my 64 429 as the plugs were burning a bit lean to correct that
The Techs at Edelbrock will tell you what to change for just Asking

A new fresh carb working correctly is a wonderful thing to have on any car restoration

Enjoy


If you have a 63 with the hydromatic trans You will need to make a braket so the trans shifts correctly
If you have the turbo 400 trans you will be fine
At 10:56pm on January 19, 2019, Jason Edge said…

Kraig, A regulator is not needed for the Edelbrock 1406 unless you are perhaps using an electric pump that pushes the psi above spec. The Edelbrock Tuning Guide on page 9 recommends a minimum of 4-5 psi, and a maximum of 6.5 psi on Page 3 of the installation guide.  Your shop manual on page shows fuel pump it idle at 5 1/4 to 6 1/2psi. These carbs are built to work within most stock fuel pump parameters.

At 7:59pm on December 15, 2017, Jason Edge said…

Welcome to the 63/64 Cadillac Website. 

This site is hosted by the CLC (Cadillac LaSalle Club) 1963/64 Cadillac Chapter. Joining the website is free to everyone, however, you must be a CLC member to join the chapter. 

- Click Here for more information on joining the 1963/64 Cadillac Chapter and the Cadillac LaSalle Club

Be sure and check out all the links and pages and make yourself at home.  The Help Page at www.help.6364cadillac.com will have links to many useful articles and information about our Cadillacs.

 
 
 

Photos

  • Add Photos
  • View All

Forum

Rear shelf deck

Started by mark zimmerman in 1963/64 Cadillac Specific Discussion 1 hour ago. 0 Replies

Hi does anyone know what yo have to do to remove the rear deck board that covers the speaker and defroster? is it screwed down ?glued?ThanksContinue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge yesterday. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

I Whipped Out My Horn and Waxed It Today!

Started by Jason Edge in General Discussion. Last reply by john w. warner on Friday. 6 Replies

This got some humorous replies on Facebook and wanted to share here on the 63/64 site.I was installing the lower hood latch with all the new gold cadmium bling on my 64 Coupe de Ville "Dino" today…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service