I am in the middle of doing a carburetor update and I am planning on blocking out the middle exhaust ports on the in manifold as per Jason's instructions on doing this update. I am going to install an Edelbrock 1406 carb with electric choke. In the instructions Jason mentions that the intake manifold gaskets should be updated to the thicker kind in order to seal around the metal plate being added to block off the exhaust passage that goes through the intake manifold on the production set up. Does any one have a place that I can order those type gaskets either online or at an auto parts store. I am only finding either the same thin type gaskets that are already on the car and won't seal properly, or what looks to be a gasket made from rubber from a company called Fel-Pro, and I don't know if those will do the trick. I know that I am not the first one to do this update so where can I get the proper gaskets from? Any suggestions will be greatly appreciated.
Tags:
Here is where I got mine https://vintagecarburetorsandgaskets.com/shop/intake-manifold-set-1...
Hey Pat ,
give me a call ,I’m in the middle of doing my carburetor project right now. I have some useful info for you .email me at schrym@aol.com I’ll send you my number
Thanks Ray.
Started by Scott Santora in General Discussion. Last reply by Dennis P. DiBari 5 hours ago. 4 Replies 0 Likes
I could use some confirmation. I sent out my radiator for my 63 De Ville to get re-cored. Several weeks later, when I went to pick it up from the service vendor, I noticed a large amount of green…Continue
Started by Jason Edge in Trivia. Last reply by Cees de Bunje 14 hours ago. 13 Replies 0 Likes
It has been a while since we did some trivia and I was watching a movie last night and saw this 1964 Coupe de Ville that briefly makes an appearance. The Trivia Question is: What Movie Is this?…Continue
Started by Todd Fox in Restoration Discussion. Last reply by Todd Fox yesterday. 2 Replies 0 Likes
Has anybody in here found a good supplier of replacement floor braces for the 64 convertibles. Continue
Started by Jason Edge in For Sale yesterday. 0 Replies 0 Likes
I just pulled a very good Cadillac Cylinder Head Water Outlet Pipe for cars with AC with the extended arm for compressor. That came off a running parts and is a nice piece. Included is a new 180…Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
ContinueApril 21, 2024 from 8pm to 9:30pm – Zoom
0 Comments 1 Like© 2024 Created by Jason Edge. Powered by