Hello, and thanks for adding to group!
I am restoring 1964 429 engine which I bought as dismantled. It is said to be smoking in driving and has been stored as parts for a year. It is most probably 65500 miles driven. Car was not driven for10 years.
The only damaged part found so far is the top of exhaust valve of cylinder #5. The top has been worn so much that the rocker has been pressing valve locks as well. Respective rocker is worn as well, much more than others. And exhaust rocker #6 is worn as well, and exhaust #8.
Then questions:
1. What damage could this cause? I can think that valve lift gets a bit smaller than it should, but so what?
2. Is that common for Cadillac 429 exhaust valves to worn from the top, especially cylinders #5 and #6? Maybe there is less oil.
This is my first V8 engine project. I have Shop manual. I plan to replace piston rings, all gaskets, nylon timing gear, some worn exhaust valves and rockers, and valve stem o-rings. Bearings, pistons and shafts are in good condition.
Big thanks in advance!
Tags:
Slowly 429 and TH400 are getting close the big moment when they will be married together with adapter ring before moving to their final home in the Engine Bay. From pile of bolts which came with the car I found some potential candidates for connection. There are 6 similar bolts + another set of 6 a bit longer bolts.
Question: should I use the longer bolts between TH400 and the ring, or between the ring and the engine?
To me it seems that both lenghts will work in both places, but of course I would like to use correct length.
Any idea anyone?
The THM to Adaptor ring are the longer bolts. Here are the specs:
- THM Trans to Adaptor Ring: 7/16"-14 1 1/2" Long Grade 5
- Adaptor Ring to Engine: 7/16"-14 1 1/4" Long Grade 5
Of course I have them cad plated but yours like in fine condition.
Thanks Jason!
I have been busy with 66 coupe and new acquisition 67 convertible but now I decided to focus in getting rebuilt engine and th400 finally into 64 Engine Bay.
Should I get good compression results in cylinders when rotating engine manually slowly from crank bolt? Reason for asking is that I get very low numbers in meter. Engine is still in engine stand.
i could install adapter ring and rotate with starter to get proper results.
I plan to use Edelbrock 1406 from my 66 for 64 engine break in. It works fine now in 66 so it should work fine in 64 as well from the beginning.
I removed radiator and AC condenser, and then it was possible to push from front and wiggle the transmission cooling pipes to their places.
Next: are all 3 wires to starter supposed to go via the bracket in exhaust manifold, or the big wire only? I try to make it as original as possible.
Getting closer to break-in step by step. Small setback was to notice the radiator is leaking a bit. I decided to take it to radiator shop to get it re-cored and maintain the original outlook.
I tested that starter works fine.
it is quite tight place to tighten the nuts of front engine mounts! Is there a trick for it? With swivel socket?
I am fighting in two frontiers because lifter replacement for 67 takes some time as well!
Original radiator has now a new core and water stays well inside.
When priming the engine with drill the pressure goes quickly to 1,4 bar but starts to go down even when I continue rotating the oil pump. Some oil comes to heads and especially to the rocker in the middle. Others stay dry. Probably I should use the drill longer?. I guess no need to open the oil pump because clearly it works. It has new gears and a new spring in valve.
When priming the oil comes fast to oil pressure sensor hole, but when I connect the meter it shows max 1,5 or zero. I need to try with new meter. Only some of the rockers get oil, and same result if I rotate the engine by hand. But it is clear that oil comes to pressure sensor and to rockers, so I think priming is ok.
I took a bit closer look to rockers and found out that the three new rockers which I have are equipped with an oil groove inside. With this groove oil is much easier to pushrod end of the rocker. The hole in original rocker never meets the hole in the rocker shaft, and oil is getting very slowly to ends of the rocker. Oil stays between the rocker andnthe shaft. That could be the reason for 429 lubrication problems. Probably I will update all rockers with improved design. You see the difference in photo below. Close to camera is new rocker with oil groove inside.
Scott Santora Online
Started by Doug Scarrow in For Sale 1 hour ago. 0 Replies 0 Likes
just listed solid 1963 1964 non tilt steering wheel. https://www.ebay.com/itm/266784089004$120 plus shippingContinue
Started by Larry Rees in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 11 hours ago. 9 Replies 0 Likes
I have a 64 Cadillac Deville convertible. When the wiper switch is turned on the washer pump activates continuosly no mater what speed is selected. Washer pump shuts off when wiper switch shut off.…Continue
Started by Russ Austin in For Sale. Last reply by Russ Austin 13 hours ago. 2 Replies 0 Likes
I have 2 working T-3 low beam headlights and numerous T-3 high beam headlights for sale. Low beams are 22 each and high beams are 15.00 each plus shipping. Please email me at russ@thecadishack.com …Continue
Started by Larry Rees in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 19 Replies 0 Likes
Neither of my cornering lights are working. I started by focusing on drivers side. I removed the entire assembly and cleaned it up, replaced the wire to the socket, cleaned and lubricated the socket…Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue© 2024 Created by Jason Edge. Powered by