Someone asked me if the exhaust manifolds have to come off to change the motor mounts? I have zero experience as I always take them off the engine last when I remove an engine and disassemble.
With that said, with my zero experience of replacing with engine in engine bay, but also looking straight at the 3 bolts/nuts on each mount on my own 64 CDV and from my inferred experience, I would think it would not be that bad if you 1) remove the 3/4" nut and washers at the mount bottom stud where it attached to the frame tower, then push the engine up slightly to get a bit of clearance (needed anyway for the bottom stud to clear the frame town) then use extensions, angle joints and sockets (or ratchet wrenches) to reach the 3 bolts, nuts & washers per mount). These are not going to be the easiest to get to but much easier than removing the exhaust manifold. They also spin pretty easy once you break the split lock washer hold.
As far as pushing the engine up a bit, I can see disconnecting the exhaust pipe to exhaust manifold connection at the rear as that would probably allow the engine to travel up a bit more, but I can't see having to completely remove the exhaust manifolds. I have removed so many of those lower 3/4" nuts I can do that blindfolded in 5 minutes, but those 3 upper smaller bolts on each side will just take some time.
OK, who has swapped out their motor mounts with engine in car? Did you remove the exhaust manifold or not? Explain your process.
thanks, Jason.
Tags:
I’m curious myself. My mounts have smushed a bit and I’ve been avoiding even the thought of getting into it.
I swapped mine out a while back (2011) with the engine in the car. It was a combined project of timing chain & rear main seal replacement as well so I had the exhaust pipe & oil pan off. I did not remove the exhaust manifolds. It was pretty much like Jason guessed: remove the nuts & bolts on the mounts and raise the engine slightly. If I remember correctly, I jacked up one side, replaced the mount, lowered it back down then repeated on the other side rather than raising the engine from the middle. I replaced the transmission mount too. It was not the most difficult job I've done on the car. After I was done, it had raised the engine far enough to cause the fan to hit the fan shroud & muffler to bang on the floor board. When I started the car these new noises caused me to say some bad words like "WTF now?" Luckily it was easy to readjust the shroud & exhaust pipe. The new mounts corrected the driveline angle and got rid of the dreaded "driveshaft rumble" these cars are prone to.
Thanks for the reply and confirming, Kurt! I was pretty sure the exhaust manifolds wouldn't need to come off.
Started by Scott Santora in General Discussion. Last reply by Dennis P. DiBari 11 hours ago. 4 Replies 0 Likes
I could use some confirmation. I sent out my radiator for my 63 De Ville to get re-cored. Several weeks later, when I went to pick it up from the service vendor, I noticed a large amount of green…Continue
Started by Jason Edge in Trivia. Last reply by Cees de Bunje 20 hours ago. 13 Replies 0 Likes
It has been a while since we did some trivia and I was watching a movie last night and saw this 1964 Coupe de Ville that briefly makes an appearance. The Trivia Question is: What Movie Is this?…Continue
Started by Todd Fox in Restoration Discussion. Last reply by Todd Fox yesterday. 2 Replies 0 Likes
Has anybody in here found a good supplier of replacement floor braces for the 64 convertibles. Continue
Started by Jason Edge in For Sale yesterday. 0 Replies 0 Likes
I just pulled a very good Cadillac Cylinder Head Water Outlet Pipe for cars with AC with the extended arm for compressor. That came off a running parts and is a nice piece. Included is a new 180…Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
ContinueApril 21, 2024 from 8pm to 9:30pm – Zoom
0 Comments 1 Like© 2024 Created by Jason Edge. Powered by