Here is another one of the tricks I learned over the years and included in our March 2013 Newsletter and will share here:
Removing the Oil Dipstick Tube
by Jason Edge
This might seem like an easy task but removing and installing a dipstick tube in an engine block without damaging the tube is not that easy, but I have a sure fire “trick” that I will share with everyone. The problem is if you just try to grip the tube with pliers and twist and turn out, or even worse take a hammer and punch out from the bottom, you are guaranteed to damage the tube.
For removing the tube, the trick is to take a deep set 11mm 12 point socket and slide on the bottom of the tube, and gently tap the socket with hammer, pushing it out. You will be able to remove the tube up to a point before the lip of the socket hits the bottom of the block. You can then take an 11mm open end wrench and put around the tube next to the seat ring and tap the wrench head with hammer to drive the tube the remainder of the way out. (Note: if tube is sliding out nice and smooth with deep set socket, you can switch to a short regular 11mm 12 point socket, once you reach the block with deep set socket, to push it through that much farther without switching to the open end wrench).
For inserting the tube, lube the block where tube is inserted with WD40 and set the 11mm open end wrench head against the seat ring and gently tap the tube into the block until the seat ring is against the block. I have removed and installed at least a dozen dip stick tubes in this manner over the years and works perfectly every time.
Note: 7/16" Socket & Wrench will work but 11mm will give you a tighter fit.
Scott Santora Online
Started by Larry Rees in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 20 hours ago. 21 Replies 1 Like
Neither of my cornering lights are working. I started by focusing on drivers side. I removed the entire assembly and cleaned it up, replaced the wire to the socket, cleaned and lubricated the socket…Continue
Started by Doug Scarrow in For Sale yesterday. 0 Replies 0 Likes
just listed solid 1963 1964 non tilt steering wheel. https://www.ebay.com/itm/266784089004$120 plus shippingContinue
Started by Larry Rees in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 9 Replies 0 Likes
I have a 64 Cadillac Deville convertible. When the wiper switch is turned on the washer pump activates continuosly no mater what speed is selected. Washer pump shuts off when wiper switch shut off.…Continue
Started by Russ Austin in For Sale. Last reply by Russ Austin yesterday. 2 Replies 0 Likes
I have 2 working T-3 low beam headlights and numerous T-3 high beam headlights for sale. Low beams are 22 each and high beams are 15.00 each plus shipping. Please email me at russ@thecadishack.com …Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue
© 2024 Created by Jason Edge.
Powered by
You need to be a member of 63/64 Cadillac Website to add comments!
Join 63/64 Cadillac Website