For Sale (340)

Featured Discussions

Chapter Member? Got a 63 or 64 Cadillac for Sale? Let's Run it in the Newsletter!

One of the new features of recent newsletters is a Member Classified Cars for Sale section. If you are a Chapter Member and have a 63 or 64…

Started by Jason EdgeLatest Reply

Discussions Replies Latest Activity

Current 1963/64 Cadillac Listings on eBay

To see all 1963/64 Cadillacs Listed on eBay in the USA CLICK HERE. The web address for this page is:  www.ebay.6364cadillac.com

Started by Jason Edge

1 on Monday
Reply by Jason Edge

Chapter Member? Got a 63 or 64 Cadillac for Sale? Let's Run it in the Newsletter!

One of the new features of recent newsletters is a Member Classified Cars for Sale section. If you are a Chapter Member and have a 63 or 64…

Started by Jason Edge

5 on Saturday
Reply by Anders

63 4 door Cadillac

Need to start parting this car out. Might be moving soon and if its not parted out, it'll be scrapped. Also have Motor and transmission fro…

Started by Walt Timmerman

6 Jun 17
Reply by Cody

Classic Cadillac Parts For Sale - Misc Items

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at www.facebook.com/classiccadillacparts and will post a fe…

Started by Jason Edge

249 Jun 17
Reply by Jason Edge

Classified Cars for Sale from June 2021 Newsletter

Here are the Six 1963/64 Cadillac Offerings in the 1963/64 Cadillac Chapter June 2021 Newsletter.  Several of these were new ads so be sure…

Started by Jason Edge

0 Jun 9

1938 LaSalle 5019 Sedan Featured in June 2021 Newsletter for Sale - $6000

This 1938 LaSalle, owned by Alfred Crutchfield is featured in our June 1963/64 Cadillac Chapter Newsletter and is for sale! Asking $6000 Lo…

Started by Jason Edge

0 Jun 2

1964 Cadillac parts for sale... northern cali

Bill Hirsch cast iron gray exhaust and manifold paint (1 can) $20 Bill hirsch Cadillac dark blue engine enamel high temp high gloss (2 can…

Started by Jason

0 May 7

1964 Cadillac Hood & pair of Fenders (with wheel wells)

I am in Northern California and I have a pair of fenders and hood plus wheel Wells all have minimal surface rust no structural rust asking…

Started by Jason

1 May 4
Reply by JoshN

drive shafts for 1964

I have two driveshafts for the 1964 with turbo hydramatic in good condition, email me at hdp10@yahoo.com

Started by William Cameron

4 Apr 25
Reply by Tony and Ginny 429

63 Sedan DeVille Parts Liquidation

Hello All my restoration is complete I have lots of parts left and want to help with your restorations Everything is for sale.....all the p…

Started by Mark Borer

6 Apr 25
Reply by Edwin Bynoe

RSS

Photos

  • Add Photos
  • View All

Forum

63 coupedebille fuel pump issues

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 5 hours ago. 20 Replies

I have a 63 cadillac and I took it to a mechanic for a motor tune up long story short the fuel pump gave out and hes tried twice to order it and he says it didnt fit the original pump is smaller on…Continue

A Before & After Example

Started by Jason Edge in Restoration Discussion yesterday. 0 Replies

Since I started cadmium plating the many fasteners and other items from the 55 and counting parts cars I have bought in (1200 lbs worth and counting), I have to say it has really taken the…Continue

Oil leaking out of oil cap breather

Started by mark zimmerman in Restoration Discussion. Last reply by mark zimmerman yesterday. 12 Replies

Hi i would like some ideas on this i replaced oil cap breather and pcv valve and still oil  coming out of breather at normal speeds down the road.This has been going on for quiet awhile from the…Continue

Update on fuel pump

Started by Daniel Grande in 1963/64 Cadillac Specific Discussion. Last reply by William R Conte yesterday. 1 Reply

I'm still looking thru land and sea for this fuel pump anyone out there know what size engine I have here are some pics of the stamps on the block I found to make sure my engine is a 390 because the…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service