Newsletters (54)

Featured Discussions

1963/64 Cadillac Chapter June 2021 Newsletter Posted

I have just completed and posted the June 2021, 1963/64 Cadillac Chapter Newsletter to our newsletter page at www.newsletters.6364Cadilla

Started by Jason EdgeLatest Reply

1963/64 Cadillac Chapter February 2021 Newsletter Posted

I have just completed and posted the February 2021, 1963/64 Cadillac Chapter Newsletter to our newsletter page at www.newsletters.6364Cadi

Started by Jason EdgeLatest Reply

Discussions Replies Latest Activity

1963/64 Cadillac Chapter June 2021 Newsletter Posted

I have just completed and posted the June 2021, 1963/64 Cadillac Chapter Newsletter to our newsletter page at www.newsletters.6364Cadilla

Started by Jason Edge

1 May 28
Reply by Jason Edge

June Newsletter Teaser

I plan to have another 1963/64 Cadillac Chapter newsletter out by June 1 and thought I would give everyone a teaser of the next feature car…

Started by Jason Edge

5 May 13
Reply by Russ Austin

1963/64 Cadillac Chapter February 2021 Newsletter Posted

I have just completed and posted the February 2021, 1963/64 Cadillac Chapter Newsletter to our newsletter page at www.newsletters.6364Cadi

Started by Jason Edge

0 Feb 17

1963/64 Cadillac Chapter January 2021 Newsletter Posted

I have just completed and posted the January 2021, 1963/64 Cadillac Chapter Newsletter to our newsletter page at www.newsletters.6364Cadil

Started by Jason Edge

1 Jan 13
Reply by Tony and Ginny 429

Jan 2021 Sneak Peak

Sneak peak of our January 2021 Newsletter Feature Cadillac. Note the 33K miles on odomenter and crackfree steering wheel. stay tuned for…

Started by Jason Edge

1 Jan 9
Reply by Jason Edge

1963/64 Cadillac Chapter December 2020 Newsletter Posted

I have just completed and posted the December 2020, 1963/64 Cadillac Chapter Newsletter to our newsletter page at www.newsletters.6364Cadi

Started by Jason Edge

0 Dec 6, 2020

Perhaps a Christmas Treat for Dino - Check out Upcoming December Newsletter

Picked this up with the complete engine and transmission setup I just bought and may be making its way onto Dino in the near future. Check…

Started by Jason Edge

1 Nov 24, 2020
Reply by Tony and Ginny 429

Upcoming December Newsletter to Feature Emma & Larry Rees' 1964 deVille Convertible

For our upcoming1963/64 Cadillac Chapter December 2021 Newsletter we will be featuring Emma & Larry Rees' 1964 de Ville Convertible wh…

Started by Jason Edge

0 Nov 23, 2020

1963/64 Cadillac Chapter October 2020 Newsletter Posted

I have just completed and posted the October 2020, 1963/64 Cadillac Chapter Newsletter to our newsletter page at www.newsletters.6364Cadil

Started by Jason Edge

0 Oct 12, 2020

1963/64 Cadillac Chapter August 2020 Newsletter Posted

I have just completed and posted the August 2020, 1963/64 Cadillac Chapter Newsletter to our newsletter page at www.newsletters.6364Cadil

Started by Jason Edge

0 Jul 31, 2020

RSS

Photos

  • Add Photos
  • View All

Forum

63 Hydra-Matic won't shift out of first

Started by Norm Waters in 1963/64 Cadillac Specific Discussion. Last reply by Norm Waters 1 hour ago. 7 Replies

Hello everyone. I had a perfectly good shifting Hydra-Matic transmission until I elected to fix the leak at the dip stick tube. I just did a quick seal with gasket maker since my current tube is…Continue

Rear brake lock up when cold

Started by Cliff Johnston in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 17 hours ago. 1 Reply

Hi everyone, ever since getting the car back on the road, the rear brakes grab when they are cold and I’m moving at slow speed.  Once I get along the road and stop they are fine. I see some posts…Continue

Vacuum advance

Started by Thomas Yarri in 1963/64 Cadillac Specific Discussion. Last reply by Thomas Yarri yesterday. 4 Replies

Good afternoon to all my fellow Cadillac owners! I have a question about the vacuum advance on my car. The car is a 64 without a/c and a Rochester carburetor. I noticed that I have vacuum at the port…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service