Wanted to Buy (414)
| Featured Discussions |
|---|
14 Tips for Buying Vintage Car Parts OnlineCheck out this link with tips on buying vintage parts I received in the Hemmings Daily Blog today: http://blog.hemmings.com/index.php/2016/… Started by Jason EdgeLatest Reply |
| Discussions | Replies | Latest Activity |
|---|---|---|
turn signal switchdoes anyone have a turn signal cable for a tilt steering wheel for sale? looks like what i have posted in the photo Started by Chris miller |
0 | Jul 16 |
Side molding for a 63 coupe.I am look for all 6 pieces of side molding for 1963 series 62 coupe. Started by MIKE |
9 |
Jul 10 Reply by Gama Reyna |
Wanted: washer fluid reservoir 1963 CadLooking to buy a good used washer fluid reservoir with cap for my '63. Started by Mark Geertsma |
7 |
Jun 28 Reply by Tony and Ginny 429 |
429 lower compression ringI am installing new rings to my 64 429 and being first time there, I managed to break one ring. I wish not to buy the complete set. Are the… Started by Matti Roth |
3 |
Jun 11 Reply by Matti Roth |
Anyone have a good driveshaft for a 63 Eldorado?Hey Guys, The ball on mine is too worn and not repairable. Anyone have a tight used one for sale? Thanks! Louie Started by Louie Hernandez |
12 |
May 26 Reply by Louie Hernandez |
WTB Various 1963 Sedan partsLooking for a have full of parts. Bottom chrome trim that the holds glass. All four sides. Tilt turn signal switch. Reflector that goes… Started by Cody |
0 | May 17 |
Windshield Washer Jets for 64 Deville neededHi, I know it's just a trivial part, but does anyone have a couple of spare windshield washer jets for a 64 Coupe Deville, I just need the… Started by Carlo Santaniello |
1 |
May 17 Reply by Jason Edge |
DevilleHi I am looking for a cadillac deville 64 convertible with A/C to restore about 10000$if you have any contact me Started by Planet-automobile |
1 |
May 9 Reply by Tony and Ginny 429 |
Looking for the following parts for 64 coupe devilleISO a oil dipstick, trunk lid, front and rear bumper also a rear window?! Started by JoshN |
1 |
May 3 Reply by Jason Edge |
Thermostat housingLooking for a clean thermostat housing (water outlet) for my 1963 390. Can anyone point me in the right direction? Having a hard time find… Started by Aaron Arroy |
1 |
Apr 15 Reply by Tony and Ginny 429 |
Photos
Members
Forum
63 Hydra-Matic won't shift out of first
Started by Norm Waters in 1963/64 Cadillac Specific Discussion. Last reply by Norm Waters 55 minutes ago. 7 Replies 0 Likes
Hello everyone. I had a perfectly good shifting Hydra-Matic transmission until I elected to fix the leak at the dip stick tube. I just did a quick seal with gasket maker since my current tube is…Continue
Rear brake lock up when cold
Started by Cliff Johnston in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 17 hours ago. 1 Reply 0 Likes
Hi everyone, ever since getting the car back on the road, the rear brakes grab when they are cold and I’m moving at slow speed. Once I get along the road and stop they are fine. I see some posts…Continue
2 timing covers. 63 390. One crossover pipe ac, harmonic balancer
Started by Kim K Kaiser in For Sale. Last reply by Kim K Kaiser 18 hours ago. 2 Replies 0 Likes
Vacuum advance
Started by Thomas Yarri in 1963/64 Cadillac Specific Discussion. Last reply by Thomas Yarri yesterday. 4 Replies 0 Likes
Good afternoon to all my fellow Cadillac owners! I have a question about the vacuum advance on my car. The car is a 64 without a/c and a Rochester carburetor. I noticed that I have vacuum at the port…Continue
Blog Posts
1963 series 62 convertible transmission issue
Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment 0 Likes
Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…
ContinueNew vehicle in the club
Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment 0 Likes
I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha. …
Torque converter grab when idling in Drive
Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments 0 Likes
Hi Everyone, been quite a while since i have been on here.
I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.
With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.
I've had the car dyno tuned and…
ContinueCan you help? Driveshaft Question....
Posted by Chris on May 30, 2021 at 8:55am 1 Comment 0 Likes
Hello!
Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…
ContinueEvents
© 2021 Created by Jason Edge.
Powered by
