Convertible Cylinder Bracket Removal
Hi, I'm hoping some of the other members here can chime in on this if they have experience with this. My convertible top motor burned out and while I was replacing it, I noticed the driver's side top cylinder was leaking. I ordered a new one and removed the current one and the bracket that attaches to it would not come off. It is held on with two philips head screws. One side came off with ease. The other completely stuck even after multiple shots of WD-40. Is one of the sides reverse threaded?
Comment
-
Comment by Chris Codd on July 31, 2014 at 8:16pm
-
Ok, so I was able to remove the bracket without removing both screws. One of the screws must be permanently fixed in place because it wouldn't budge. After removing the screw from one side (with absolute ease), I wedged the bracket in a c-clamp and a quick twist of the cylinder and it was out.
Photos
Members
Forum
Troubleshooting drivability
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by Jordan Johansen-Moe 22 hours ago. 3 Replies 0 Likes
Hey everyone. Last year I had some trouble keeping the Caddy running. A little backstory, car hadn’t ran in 30 years. Rebuilt the crankshaft. I had it running pretty well for a bit. Even drove it the…Continue
T3 Headlights
Started by Jeff Donaldson in General Discussion yesterday. 0 Replies 0 Likes
Has anyone bought new oem headlights from Lectric Limited? They want $150 for a set of new remanufactured ones. Any advice would be appreciated.JeffContinue
Headed to Birmingham Tomorrow!
Started by Jason Edge in General Discussion on Friday. 0 Replies 0 Likes
I have been quiet lately, and just wanted to jump in an chat a minute. I have back to back visits to potential CLC Winter Board and Grand National Sites, not to mention I have been pushing to get…Continue
On Busy Day Yesterday!
Started by Jason Edge in General Discussion on Friday. 0 Replies 0 Likes
Very busy day working the parts cars yesterday, pulling engine and transmission out parts car #59, getting parts car #60 off the car hauler, then parts car back up on car hauler for final…Continue
Blog Posts
Loud air moving sound within carb with cleaner removed
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Vintage Air AC
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
accumulator dryer
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
'63 Eldorado trumpet horn + 2 standard horns restoration
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
ContinueEvents
© 2024 Created by Jason Edge.
Powered by
You need to be a member of 63/64 Cadillac Website to add comments!
Join 63/64 Cadillac Website