All Discussions Tagged 'classiccadillacparts' (6)

Discussions Replies Latest Activity

Classic Cadillac Parts For Sale - Misc Items

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at www.facebook.com/classiccadillacparts and will post a fe…

Started by Jason Edge

157 yesterday
Reply by Jason Edge

1961-64 Cadillac Rims, New Old Stock 235-75-15 Tires

Click Here for more pictures on my Facebook Classic Cadillac Parts page. $200 for complete set of 4 previously painted 1961-64 Cadillac Ri…

Started by Jason Edge

2 Dec 28, 2014
Reply by Jason Edge

Excellent Set of 1964 to 1967 429 Heads, Cleaned, Magnafluxed, Ready to Rebuild - $200

I've got a good selection of cylinder heads and have started taking them in and having them cleaned and magnafluxed to check for cracks, an…

Started by Jason Edge

1 Aug 14, 2014
Reply by Jason Edge

1963-67 Thermostat and Water Inlet Housing - $25 + s/h

Cleaned, bead blasted, bottom planed smooth and flat, and any corrosion on neck filled with JB Weld, primed and painted with correct Bill…

Started by Jason Edge

1 Jul 25, 2014
Reply by Jason Edge

Restored 63/64 Cadillac Oil Filler Cap - $35

Very hard to find the original oil filler cap and find one undented. This one has been cleaned, restored, and painted. Email me at jasoned…

Started by Jason Edge

0 Jul 23, 2014

Wanted: 1963 & 1964 Parts Cars Within 250 Miles of Central NC

I am always in the market for a complete or almost complete parts car. If you have one or know of a potential 1963 or 1964 Cadillac parts…

Started by Jason Edge

0 Jun 8, 2014

RSS

Photos

  • Add Photos
  • View All

Forum

A Drilling No-No .... That Worked!

Started by Jason Edge in General Discussion. Last reply by Jason Edge 1 hour ago. 16 Replies

Thought I would share a quick story regarding something I did that I generally do not recommend - Free handed drilling a broken front engine cover bolt.  Before I jump into it I will say I do not…Continue

Exhaust manifold: Repair, replace or headers?

Started by Dutch Dickinsen in General Discussion. Last reply by Tony and Ginny 429 6 hours ago. 1 Reply

My newly acquired '64 Coupe DeVille suffers from a cracked right side exhaust manifold.It looks like my options are limited to rolling the dice on a used manifold, converting to headers or seeing if…Continue

Tags: 429, manifold, exhaust

Steering Wheel

Started by Mark Borer in General Discussion 10 hours ago. 0 Replies

plz watch this videoIt shows play between the 2 cylinders that make up my columni have tightened everything up as best as I can....but it moves a bitthe lower cover had a screw that lined it up, and…Continue

Help! I need a 1964 Eldorado front left fender.

Started by Jorge M in Wanted to Buy. Last reply by Jon Ettman 12 hours ago. 5 Replies

Help looking for a 1964 Eldorado front fender for a convertible.Thank you please contact djjmoreno84@gmail.comContinue

Blog Posts

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 6 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …

Continue

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Upper A Arm Rubber Bumpers

Posted by Gene McIlroy on August 12, 2019 at 1:30pm 3 Comments

I have found a very good replacement part for the Upper A Arm Bumpers.  The top part is identical to the originals the bottom can be used as is or after a few minutes with a belt sander can be ground to the V shape as the originals were.  The replacement bumpers are for a 2001 to 2005 S10 Sanoma or Blazer.  Part number is on the box in the photos.  First photo is the box next to the box is the S10 part and an original.  Next photo shows my sanded down part next to an original.…

Continue

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service