Didnt happen. :-).      Was up to tge point of putting in antifreeze.   

And hv leak coming out of water pump seal, so, im going back in.  Any tips in meantime afa sealanants, gasket seals, etc would be helpful as i break it down again.  

I was gettn jazzed!   Mustard fell off the dog when i heard the fluid hittn the floor

Views: 46

Reply to This

Replies to This Discussion

Post removed due to rethinking the info posted 

Kim 
Best to pull it apart and redo 

- as you do not want coolant blowing around from the fan when trying to run the engine for the very first break in run of one half hour as that is to distracting to do with that going on 

Will just make the process more difficult to be doing at that time 

I will suggest using — Permatex  on the— two O rings as that will insure a leak free joint that will last just about forever as mine has 

Enjoy 

It was around the bottom.  

Permatex is —very fast drying —-which makes it a pleasure to use unlike silicone that takes 6 hours   to dry  so you can get the job completed faster 

It will be dry by the time you reset the crossover 

Not to bad a job  to be removing the cross over pipe and reinstall it —-so do that and get the leak gone so the engine and you will not be covered in coolant from the fan with the engine running for the 1/2 hour run up 

You need to keep the engine running continually during that time 

OH — it Always Leaks From the Bottom 

From my experience in life mostly from my hobbies the thing that separates the men from the boys is that when something does not go right the men are sure to back up and fix the thing that wrong ( needs redoing ) before you  proceed  forward 

We are getting Close Now !!!!!!!!!!!!!!!

Enjoy 

Kim 

I am hoping this note will inspire your mechanical adventure with your Cadillac which made me reflect  on  my earliest days just starting to work on a car 

When  I got my brand new 1963 Chevy 409 425 HP 4 speed—— I had never worked on a car before ( I was 21years old ) with no known mechanical ability ( yet ) 

The first time I installed new points in the car —-the car stopped dead on me 3 blocks from my house —as I forgot to tighten them down 

I was determined to learn all I could to make that car run as good as it was possible and go  drag racing 

Drag racing was in the air in the early 60’s with the muscle cars coming out of Detroit and  the music on the radio 

I was spending many nights at the local burger joints  where many of the hot shot car guys would be

hanging out and  be leave  ther to street race to be testing there cars parts and  adjustments 

These boys were very accomplished drag racing ( a number of class champion record holders ) and I learned so very much from them and little by little became one of the accomplished drag racers myself 

So I went from breaking down 3 blocks from my house —to breaking the local track record in Super Stock having done 90% of the work on the car myself 

Your desire to do and learn to repair your Cadillac —very much reminds me —-of my own quest to do and lean what I needed to do to accomplish my car goals 

For that reason I am getting a  —very big KICK —out of your determination to do the same 

In many ways you are reminding me —of me in those days and I am  FAN of yours for that reason 

There was —No Internet to consult  for any  information in those days ! ( if you could possibly imagine that !! ) 

Rock on - !  as you are developing more hands on knowledge about your  very own Cadillac than many may ever do —— Priceless !     ( if it wasn’t so  dame expensive — LOL ! ) 

Enjoy 

Thanks Tony,  im.plugging at it still.

RSS

Photos

  • Add Photos
  • View All

Forum

Start up. 1st attempt

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 6 hours ago. 21 Replies

No Description

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 10 hours ago. 234 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

64 Horns

Started by John Inglesby in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Saturday. 1 Reply

I have 3 horns and the only one working is the bottom long one. The 2 round ones are not. I played around with the connections and they seem ok. I tried to check for power but not sure I was doing it…Continue

Compression test

Started by Michael Chomout in Restoration Discussion. Last reply by Karl Schwarz on Friday. 8 Replies

Dear Gents, just had time to dova compression test on the 429 engine by warming up the engine and removed all plugs and went through cranking without pouring oil into the cylinder since I want to…Continue

Blog Posts

63 Trunk detail

Posted by Bob Pontius on April 8, 2021 at 3:07pm 1 Comment

Jason, I liked the detail and information you have provided. I would like to do mine similar to yours. Can you help? Do you have trunk material? OPGI is sending the trunk product for my 63 Fleetwood. But it does cover the entire trunk as yours was done. If you do not have can you give me a reference? Thanks!! Bob

Car lift and jack stands

Posted by Les Eastling on March 23, 2021 at 10:00am 4 Comments

I mentioned during the 63/64 chapter zoom meeting on 3/21 that we had installed a car lift in our garage. Someone asked what kind and I didn't have the info at hand, so here is a link to it and also a link to some tall jack stands we use to add more stability to the car and an additional safety factor. There is something about getting underneath one of these cars that makes me a little nervous! …

Continue

Leaky Freeze Plug

Posted by Lee Martin on March 22, 2021 at 12:49pm 7 Comments

Just developed a significant leak coming from a freeze plug right over the starter.  Would this be considered a "cam plug" i.e. like Dorman 17616DS?  Our cars have multiple sizes of plugs on engine block and I want to get the right one.  Also, does anyone know how pricey this is for a shop to fix?  Thanks!

Balancer location

Posted by Kim K Kaiser on March 20, 2021 at 4:47pm 6 Comments

Readi g another thread. Does this look about right on balancer gap? Thats a 1/4 thick piece of metal.

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service