With the RH passenger door mirrors now available, there will be many looking to install one on their 1963 or 1964 Cadillac. A template aligned with the edges of your door, showing the exact location of the 3 holes would be ideal, however, I thought I would share the specs on the holes you will need to install your mirror since my 1964 Coupe de Ville came with the rare dealer installed RH mirror.
FIRST: I recommend removing your LH mirror. To remove you simply loosen the Allen screw in mirror control handle and remove the retaining screw at front top of the door. Slide mirror back and it will lift up and off the door. You will be left with an excellent template for the RH door mirror. The only difference will be you will not need the larger center mounting hole on the RH mirror. See below for details.
There are many ways to make measurements of the 3 holes on the top, however, this is what I did:
1) I measured from top door ridge up to bottom of mirror hole. Since the mirror holes are basically parallel to the top door ridge, each measured 3 71/6" from the ridge line.
2) I measured from front door edge back to the forward edge of the hole. Measurements were 2 3/16", 3 11/16", and 5 3/16" starting at front hole.
3) I measured diameter of the hole. They are 3/4" in diameter. Note on the LH door more the center hold is 7/8" in diameter due to the center control rod. Since the RH mirror does not have the control rod, you only need a smaller hole for the mirror arm base attachment, and only need a 3/4" hole.
- Attaching Screw Hole in front top of Door. Look at your LH door front top where attaching bolt goes. The RH door mirror attaching screw goes in same location on the RH door. There is a roundish area where the screw hole needs to be drilled. Drill a 3/8" hole in the very center of the round attaching area. (Note from the factory, I get measurements of 7/16" but do not believe it needs to be that big... just enough to move the screw around to find the thread in the base of the drill.
- LH Driver Door Mirror Comparison. For a sanity check, I compared all measurements above to LH core doors I have on and all measurements were consistent with and approximate to the RH mirror hole specs above.
I hope that helps in the installation of your RH mirror! Below are pictures I took that go along with the description above:
Here is a picture of the RH mirror installed on my 1964 Coupe de Ville:
Tags:
I have the template to drill the holes, if anyone needs it. Just drop me an email, and I will send it to you for free.
Hi if you still have a template could you please send me one. Thanx
Mark, send me an email and I will reply with the factory template. russ85747@hotmail.com
Added link to our Help Page.
Scott Santora Online
Started by Larry Rees in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 19 hours ago. 21 Replies 1 Like
Neither of my cornering lights are working. I started by focusing on drivers side. I removed the entire assembly and cleaned it up, replaced the wire to the socket, cleaned and lubricated the socket…Continue
Started by Doug Scarrow in For Sale yesterday. 0 Replies 0 Likes
just listed solid 1963 1964 non tilt steering wheel. https://www.ebay.com/itm/266784089004$120 plus shippingContinue
Started by Larry Rees in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 9 Replies 0 Likes
I have a 64 Cadillac Deville convertible. When the wiper switch is turned on the washer pump activates continuosly no mater what speed is selected. Washer pump shuts off when wiper switch shut off.…Continue
Started by Russ Austin in For Sale. Last reply by Russ Austin yesterday. 2 Replies 0 Likes
I have 2 working T-3 low beam headlights and numerous T-3 high beam headlights for sale. Low beams are 22 each and high beams are 15.00 each plus shipping. Please email me at russ@thecadishack.com …Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 0 Likes
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue© 2024 Created by Jason Edge. Powered by