RH Passenger Door Mirror Installation - New Holes Needed in Door

With the RH passenger door mirrors now available, there will be many looking to install one on their 1963 or 1964 Cadillac. A template aligned with the edges of your door, showing the exact location of the 3 holes would be ideal, however, I thought I would share the specs on the holes you will need to install your mirror since my 1964 Coupe de Ville came with the rare dealer installed RH mirror.  

FIRST: I recommend removing your LH mirror. To remove you simply loosen the Allen screw in mirror control handle and remove the retaining screw at front top of the door. Slide mirror back and it will lift up and off the door. You will be left with an excellent template for the RH door mirror. The only difference will be you will not need the larger center mounting hole on the RH mirror. See below for details.

There are many ways to make measurements of the 3 holes on the top, however, this is what I did:
1) I measured from top door ridge up to bottom of mirror hole.  Since the mirror holes are basically parallel to the top door ridge, each measured 3 71/6" from the ridge line.

2) I measured from front door edge back to the forward edge of the hole. Measurements were 2 3/16", 3 11/16", and 5 3/16" starting at front hole.

3) I measured diameter of the hole. They are 3/4" in diameter. Note on the LH door more the center hold is 7/8" in diameter due to the center control rod. Since the RH mirror does not have the control rod, you only need a smaller hole for the mirror arm base attachment, and only need a 3/4" hole.

- Attaching Screw Hole in front top of Door. Look at your LH door front top where attaching bolt goes. The RH door mirror attaching screw goes in same location on the RH door. There is a roundish area where the screw hole needs to be drilled.  Drill a 3/8" hole in the very center of the round attaching area. (Note from the factory, I get measurements of 7/16" but do not believe it needs to be that big... just enough to move the screw around to find the thread in the base of the drill.  

- LH Driver Door Mirror Comparison. For a sanity check, I compared all measurements above to LH core doors I have on and all measurements were consistent with and approximate to the RH mirror hole specs above.    

I hope that helps in the installation of your RH mirror! Below are pictures I took that go along with the description above:

Here is a picture of the RH mirror installed on my 1964 Coupe de Ville:

Facebook Facebook

Views: 1041

Reply to This

Replies to This Discussion

I have the template to drill the holes, if anyone needs it.  Just drop me an email, and I will send it to you for free.

russ85747@Hotmail.com 

Hi if you still have a template could you please send me one. Thanx

Mark, send me an email and I will reply with the factory template.   russ85747@hotmail.com 

Added link to our Help Page.

RSS

Photos

  • Add Photos
  • View All

Forum

The $120,000 1963 Eldorado on Bring a Trailer

Started by Jason Edge in General Discussion. Last reply by Jason Edge 1 minute ago. 7 Replies

I have got a flood of email, texts, about the 63 Eldo that recently bid up to $120,000 and thought I would share for those that have not seen it.Here is the link:…Continue

Fuel Supply System - Check Points Beyond the Fuel Pump

Started by Jason Edge in General Discussion yesterday. 0 Replies

Incredibly, in 3 days I have had 3 people ask about replacing their fuel pump or even adding an electric fuel pump because there carb is not getting gas.  It has gotten to the point I have copied and…Continue

Tags: System, Delivery, Fuel

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 13 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Houston we have a problem!

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Monday. 3 Replies

While enjoying the fruits of my labor on all new rear suspension and…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service