Over weekend, i intend to remove the block from engine. I was reading manual on such and in the descriotion, of remove wo trans i became somewhat confused. Is the flywheel.attached to the flexplate?
Do i also need to remove flexplate as i am pulling flywheel because the machinst needed it and HB to balance as i read they were externally balanced.
Im at the point of everything is off but the engine trans connection and engine to frame. Any tip or suggestion not outlined in book would be appreciated. Manual assumes a seasoned professional sometimes so there descriptions can be a little vague to a first timer.
Thanks in advance
Tags:
Ok, that sounds simple enough, thanks
Ok, got those 4 bolts undone. To be clear, when the engine breaks free, is anything going to drop or fall out where I need to put some kind of cushion or pad to break the fall?.
ok, i dont know about locking converter, as it made no note of it so that will have to be explained.
Additionally, after removing the four nuts from the bolts that hold the flywheel to the flex plate (i am assuming the flexplate is the brassy colored part that sits in front of and attaches to the flywheel)
Remove four nuts that hold flex plate to transmission flywheel. (I DID THIS)
DO i need to remove these other nuts (8) as i have circled in the picture?? I dont know enough about the order of things to know what is attached to what behind there and dont want to bend or twist anything. ( i noted in a thread a few years ago, someone bent the plate upon removal) thus my question.
I dont see anywhere it says remove 8 more nuts, but wont the whole piece come out,, flywheel and flexplate, the flywheel is behind the flexplate, is that what i should expect to come out?
Kim, You don't remove the flywheel to torus nuts, just the 4 flywheel to flexplate nuts you have already removed. Follow the instructions exactly and you will be fine.
I think Cees is referring to removing a 1964 429 engine with the Turbo Hydramatic where the shop manual under the Turbo Hydramatic Engine Removal Section indicates to strap the torque converter to the transmission case since the Turque Converter, unlike the Toruse used on the Hydramatic, is loose and not attached to the transmission and will side off the front shaft if the transmission tilts.
Again, follow your instructions and you will be fine. If you make up new steps you will just cause more work for yourself.
Be glad to. I hope to hook up to the engine and pull out tomoro...once out. I will remove oil pan, valve covers, front cover stuff for paint removal and repainting. Taking flywheel and HB to mill shop tues so they can balance crank. Hopeing pistons will come in this week so he can get the piston pins put in and cam bearings and camshaft put in. In mean time, i wilget all the bolt holes and nuts worked on, clean out bay, cut all the oil off the bottom of frame from the bearing leak over last couple years, and respray the bay area.
I hv put all my nuts and bolts in baggies and id ed them for reinstall. So plenty to do whike waiting on pistons and remaing camshaft work at mill shop
At least thats the plan going into tomorow
I had planned on that.
Had a Casualty of removal today. The engine was a real beast to slid off at the trans. One screw end kept hanging up on the flexplate, after acseries of lifting car, lowering car, lifting engine lowering engine, maybe 5 or six times. It finally came off. In tge process. A shiny piece of metal that was on the shaft extension got bent off. Looks like a metal s sleeve that sat under the flexplate. I cked the transmission manual and i dontvseeva blow up of that part. So, if anyone knows wat it is and were to get one, guess i need to get an order in.
On a second note, getting this thibg back in cant be any picknick. Am i correct?
Started by Jeff Donaldson in General Discussion. Last reply by Marty Smith 23 hours ago. 2 Replies 0 Likes
Has anyone bought new oem headlights from Lectric Limited? They want $150 for a set of new remanufactured ones. Any advice would be appreciated.JeffContinue
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 5 Replies 0 Likes
Hey everyone. Last year I had some trouble keeping the Caddy running. A little backstory, car hadn’t ran in 30 years. Rebuilt the crankshaft. I had it running pretty well for a bit. Even drove it the…Continue
Started by Doug Scarrow in For Sale yesterday. 0 Replies 0 Likes
Just listed very good 8619952 Cadillac front pump complete. $160 plus shipping https://www.ebay.com/itm/266805513612Continue
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue© 2024 Created by Jason Edge. Powered by