Can someone advise the best way to replace the parking light bulb? Thanks
Tags:
What lenses?
The front parking/turn signal bulb. I can't remove the chrome grill in front of the lens to access the bulb.
Remove the 4 screws, 2 up top & 2 at bottom and pull the chrome park light grill off.
The lens sometimes stick to the gasket. Liberally spray the perimeter with WD40 and take a small flat screwdriver and gently pry the lens off the gasket. Once it starts coming off it usually comes right off.
A trick for getting the bulb out since they can sometimes be hard to push in and turn at the same time, is to use a large rubber hose, like a 3/4" or size that is just smaller than diameter of bulb with a good length, a foot or so, so you can push onto bulb and twist and turn. Before you replace the bulb, disconnect battery (or just make sure lights are off) and take a needle nose and gently pull that center contact wire and spring back and forth to make sure it will push the contact up to bottom of bulb.
Yes I tried that but there is not enough clearance to pull out the grill. I think I have an issue with bumper alignment.
I had that with the last parts car. Take flat pry bar and and wrap flat end in cloth and wedge above the top of park light grill and beneath the headlight eyebrow trim and assembly that protrudes forward and gently lift up enough to get the top screws out and/or the grill to come out. Don't use too much pressure but you will be surprised there is usually enough movement to get access to the park light grill screws and pull it off. If you still cannot get enough room I would start with "hanger" bracket that goes from upper outer bumper end to the inside front bottom of fender. That should relieve some pressure to attempt the pry bar quick trick. If that fails you will may need to loose the large bumper bolts and drop entire assembly. My bet is the pry bar trick will work.
Here is a quick pic of the hanger bracket. There is one 1/2" hex bolt from bottom that screws up into a flat square washer. Might be easier to get to from bottom rather than removing batter. I would just try a flat pry bar first.
This may have to wait until after the GN. Thanks
Started by Jason Edge in Trivia 17 hours ago. 0 Replies 0 Likes
Here is another part I have seen many times but might not be familiar to many and will post up as our next trivia question.So, looking at the pictures below ... WHAT IS IT?…Continue
Started by Jason Edge in 1963/64 Cadillac Specific Discussion yesterday. 0 Replies 0 Likes
So, I get the question about headers for our car from time to time, including an email this morning.Here is my standard response:"Sanderson Headers is the only company I have never known to make…Continue
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Sunday. 1 Reply 0 Likes
Is the knob on the end of the shift lever removable? if so, how?Continue
Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Sunday. 0 Replies 5 Likes
To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue
Tags: ebay
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 0 Likes
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
Posted by Chase on March 21, 2024 at 5:55am 0 Comments 1 Like
Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!
Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments 0 Likes
Who rebuilds original AC accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year , There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A What is everyone using ? I would prefer to be as original as possible. Thanks
Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment 0 Likes
My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns.
There is a restoration service called The Horn Works who my son…
Continue
© 2024 Created by Jason Edge.
Powered by